HELP!!!! My 3310 cannot turn on after flashing!

[bulat]

I need help. Im a beginner and i need help !

I just flash my 3310 to 3315 using Rolis. And now the phone cannot ON!!! How do i restore the backup flash?

HELP:( :( :( :( :(


I use Knok to Erase the whole flash, cant do it!

I tried to flash back using my backup flash file, command "cannot prepare phone"

pls help

[gatsby76]

when u have flashed it did u correct the imei, sp locks and also then update faid ?

Easiest way is to use nokia tool v1.8 by rolis and Knok seems to be the most reliable flasher too !!!

Try again and if it still says cant prepare fone, when u set up knok and then start to flash, stick the charger in the bottom of the fone !!!

[bulat]

i tried to use knox again. this time i put in the charger. but there is no charging indicator.

And i use knok to erase the flash again, it says CANNOT INITIALISE DEVICE & then PRIVLEGED INSTRUCTION

[bulat]

After i restart my computer (winxp) i used Knok22 again to Erash the flash, and it goes until CANNOT ANALYZE PHONE. What should i do? did i spoil the phone?

[diego]

try to write again the 3315 fulflash to your phone. be sure that your phone is really 3310. if 3330, the phone will not switch on. just use rolis 478

@ gatsby
can you use nok tool 1.8 if the phone cant turn on.........? NO

[bulat]

Originally posted by diego
try to write again the 3315 fulflash to your phone. be sure that your phone is really 3310. if 3330, the phone will not switch on. just use rolis 478

@ gatsby
can you use nok tool 1.8 if the phone cant turn on.........? NO


Ive flashed the 3310 back to V5.57. And after awhile i can switch on the phone but CONTACT SERVICE. Can i 'save'my phone now?

[melakamobile]

Ok now u can just check ur phone with wintesla!!!It will show what wrong with ur phone!!!I think u have to flash ur phone with a clean eeprom!!Please send result

[bulat]

Originally posted by melakamobile
Ok now u can just check ur phone with wintesla!!!It will show what wrong with ur phone!!!I think u have to flash ur phone with a clean eeprom!!Please send result

I have Wintelsa, but how do i use it?

[Janus]

bulat,if you erase WHOLE flash with knok u must write eeprom too,not only flash!Check if it's 3310 or 3330,the size of flash is bigger at 3330.I put here both EEPROM's,3310 and 3330.

[abuissa]

bulat: take off the batery and try to flash the phone with a MCU+PPM flash then a virgin eeprom. It should work. If you want to convert your 3310 in 3315, you don't need to flash the phone.
Check here: http://www.gsmschwantz.com/3310.htm

[bulat]

I was working with the phone until 5am !! (malaysian Time)

Now i can always restore the backup flash without problems, on Knok22. But i always get flash read/write from Rolis478, why is that so?

This is what i have done so far;

I flashed back the original flash and it worked fine. Then i flashed the 3310v557.fls (or) Projectz.fls , i get SIM CARD NOT ACCEPTED. Why is that so?

How can i make it work?

I tried flashing the 3310v557.fls. Flashing ok BUT i go into the Quick Set Faid. Message is CANNOT ANALYZE PHONE. Of coz i used the MBUS cable.

[bulat]

Do u guys have any flashes for 3310-3315 to work with malaysian network?

I also can be contacted at MSN Messenger at [email protected]

[melakamobile]

Hey bulat the ''sim card not accepted'' u can just use noktool 1.8 to change the imei ,clear sp-lock ,and update faid .!!! U no need to use knok to quick set faid ,u just have to use noktool 1.8 to update faid !!!I have flash for 3310-3315 to work with malaysian network too!!!

[Phusuke]

hmmmmmm

y dont u guys do it step by step one at a time

erase the whole flash with know any version

then flash it with rolis whatever version u have there and make sure u got a working flash or if u have other fones there which is similar to urs u can back it up and use it on ur fone if it is a 5.57 version or higher then it is much better

then use knok again to update the faid, set the imei, reset full factory settings, convert it to 3315 and then update the faid again and restart the fone

if it still doesnt work try to find someone who can assist you personally to attend to ur problem.

cheers mahn... goodluck!!!

[bulat]

to all u guys out there who helped me, THANK YOU!!!!

I really appreciate it and i respect you all. I really needed the help.

Thanks Again!!!!