View Full Version : 9110 Flash phone & PDA ???
FEJS_VIP
28-01-2003, 12:52 AM
Hello!
I have small problem.
I have Nokia 9110 with german language. Please help me flash phone & pda to english. What i need. I have MBUS and Flasher DEJAN for dct-3 Please. Where I find full flash for PDA and phone?
I search everything and nothing :(! How i can flash?
Plz help
Thanks!
[email protected]
-=(FEJS)=-
Backup your 9110.
Make sure you have backup your 9110.
Make sure you made sure you have backup your 9110.
You'll need these two zip files
704mmc.zip (http://groups.yahoo.com/group/Nokia_Communicator_9110/files/SW_UPDATE/704mmc.zip) = PDA update files
cmt_601.zip (http://groups.yahoo.com/group/Nokia_Communicator_9110/files/SW_UPDATE/cmt_601.zip)= phone flash files
You may also want to download winimage (http://groups.yahoo.com/group/Nokia_Communicator_9110/files/SW_UPDATE/winimage.zip)
This will enable you to extract files from uk704mmc.img (inside 704mmc.zip)
N.B. You'll need to join
http://groups.yahoo.com/group/Nokia_Communicator_9110
in order to download the files.
How TO :-
************************
****Flash phone PART****
************************
You'll Need :-
MBUS cable
Flasher Cable
1)remove sicker under battery
'Use Only Nokia specified Li-ion Battery'
hold phone up right pin 1 is to the left.
connect pin 15-16.
Connect battery.
On screen (top left in small text) should say
'relink mode enabled'
can now flash as 5110.
2)use wt2dejan - convert rae2n06.010 = MCU and
rae2n06.01a = PPM - A - ENGLISH
N.B. files are inside cmt_601.zip.
3)Using 'Nokia Flasher v1.00b' by Dejan Kaljevic
write converted MCU @ 0x00200000 and then
write converted PPM @ 0x002f0000
4)use eeprom tools - Bottom left button 'Update AuthorityID'.
5)Disconnect pin 15-16.
6)All should be done now done:D
***********************
****Update PDA Part****
***********************
You'll Need 4MB (or more) MMC and some knowledge of how to use DOS would help.
If you don't have
DOS Prompt Launcher by Dave Chapman (http://www.dchapman.com/freeware/dos9k/dosprmpt.zip)
Then you'll have to get it and install it to the communicator's memory
1)Inside 704mmc.zip you'll find uk704mmc.img
This is a 4MB disk image.
using winimage open uk704mmc.img and extract all the files.
Copy the extracted files onto a MMC. (If not already put MMC into your 9110)
The files are:-
autoexec.bat - 27 bytes
command.com - 81,130 bytes
dos.sys - 40,198 bytes
spock.hdr - 20 bytes
spock.lzs - 3,577,796 bytes
swupdate.exe - 35,186 bytes
2)remove sicker under battery
'Use Only Nokia specified Li-ion Battery'
hold phone up right pin 1 is to the left.
connect pin 1-4.
3)Run DOS Prompt and find the files you copied to your mmc
run swupdate.exe
YOU should see a a bar process bar along the top. This process should only take about 2mins.
N.B
MMC is Drive A:
If you used PC Suite to copy the files to your mmc theyll be under
nokia\document\mmc
4)Once finished remove PIN 1 - 4.
5)You're done:)
**************
****Extras****
**************
Remove battery then press and hold
1)To format - shift + tab + f
2)Check drive for errors - shift + tab + left
3)Delete state files - shift + tab + right
4)Debugging!! - shift + d + b
5)Debugging!! - shift + d + o
then connect battery.
Karl
FEJS_VIP
28-01-2003, 10:46 PM
Thanks!
I read this :)
But i can't download this files :( I don't know why.
I have GetRigh. When I click for the start downloading i see this warning? Why?
Maybe you can mail to me and send this files?
And i have another question...
Can i flash PDA side when i don't have Multimedia Card?
And how?
I don't have one...:(
Thanks
Sorry for my english :)
FEJS_VIP
28-01-2003, 11:25 PM
OK.
Sorry. I download this files.
Can I flash PDA when i don't have Memory Card?
And how?
Thanks.
lonegunman
06-03-2003, 12:43 AM
No you need MMC card.
tech255
09-04-2003, 12:14 PM
have followed the instructions to the letter but when you run swupdate.exe it started to update the software got to about 50% and dropped out then rebooted and now i have an xip checksum error how do you get it back to dos to restart it or is it deceased..:confused:
sk8ter
13-08-2003, 01:45 PM
I'll publish bepictured instructions on my website http://www.skloss.de in english in a few days.
It's already available in german.:D
Powered by vBulletin® Version 4.2.0 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.