Start Up Tone !! HELP NEEDED !!

[paul_y2k_2]

I was wondering if anyone kind enough could add a start up tone to my file below and post it back up its a 8250 v 6.00 For my 8210


Can any one add a start up tone on this file for me a.s.a.p

File wont attch :(:( Ask me if you need it

Regards
Paul

[vatics]

Try to post it!!!!

I'll try to put a start up tone for U!!!!

[Artangel]

use MCU Tool by Azy... it is an easy tool to patch startup tone... or download Crister's tutorial...

http://artangel96.tripod.com/HOW.zip

or download it ...

http://artangel.cjb.net/

your request fls file is already finished...


:D

[pawaka]

if u wish to do it manual style using hexedit ( can be found using Search function .. use it if u need more specific subjects)

this method was originally well explained by NokDoc somewhere
in this forum...again , please use Search funtion ..but anyway i'll try to explain it here .. :D

1. Open ur .fls file using Hexeditor
2. do a search (CTRL+F) for Hex Values 0001FFA7(in case of 3210
use 0001FFA6)
3. Look at Program Status Bar for an offset value eg 0011BE3C .
4. Add 200000 so it would be 0021BE3C then do a search for Hex Values of 0021BE3C . This is ur Tone Pointer (need to change this
later on) . Now write on paper this offset address (the offset address is on the status bar )
5. Search for a Text String for ppm(if u have editted the file using PPMEdit ,u'll find the text PPMEdit by Tnp somewhere after the search) ...
6. Next , open ur tone file(with .re extension) , copy and paste it
exactly the same bytes ( higlight all tone data beginning with 02FC and ending with 070B and look at the status bar , u'll see bytes total of the highlighted tone) .
7. How to paste the same bytes ? After Step 5 , u'll find some data begin with FFFF FFFF FFFF , this is where u shall paste the data copied in Step 6 . Now u have to remember the tone begin offset (just put the cursor next before the 02fc and look for the offset at the status bar)
8. If u wish to edit the tone so it wont vibrate at all , better paste the copied data(from the tone file) into new file .
9. (in case if u paste it into new file) ... First u have to replace the last data , which is 070B with 0B0C , this is to stop the tone from looping . U can also replace hex data 0A01 to 0AFE in order to stop tone vibrating .
10. Copy the editted tone data , and paste the same bytes to ur .fls file .
11. Now go to Tone Pointer offset ( in Step 4) . Change the address to match the pasted tone data (offset just before 02FC in Step 10) eg . if u paste it at address 0012B946 ( begin of 02FC)
so u change the address to 0032B946 .
12. Save the file with different file name .
13. Open the file using PPM Manager and correct the PPM checksum . Save the file .
14. Don't worry about the MCU chksum , your flasher(tested on Rolis Flasher) will alert u of bad MCU checksum , correct the chksum if the pop-up menu appear on ur flasher program)
15. Flash the phone . Done .

Hope this would help .. and please correct me if i missed something important . TQ ..

[paul_y2k_2]

@vatics --- Download the flash file from the link below

Flash File Here (http://www.themadsite.pwp.blueyonder.co.uk/flash.zip)

Please download and add the start up tone and either mail me it or post the file on here with the start up tone added and if any one else can do it for me i would be greatfull


Regards
Paul

[Futura]

artangel no of your downloads work you get redirected to a tripod hosting page