3210 death after flash

[dzonder]

i have started flashing the 3210 with winDLS, when the program whos in errasing flash mode i lost power on my computer, now the phone dont wont to power on ewen the winDLS whont to read info abaut him
Please help me

[newcasper]

use windls
and press on forced download
no need to powere on the phone
u can do that while the phone is off
but be sure that u choose the right model of the phone

[dzonder]

ok batt therre is a message "error setting flash mode", Or its starts but verry fast and staks in 02000f keep working and to the end is the same message

[ryan_chong]

Hi~

Try to use Rolis477 or 478.Get a working full flash files and flash it.Last time i've accidently removed the flasher cable connection while flashing and the phone can't power on afterwards.But i flash it again with the same way and it's fine.U can't power on ur phone if there's interuption while flashing but u can still flash it with Rolis 477 or 478.I dunno much more bout winDLS coz i never used b4...But i'm sure it can be done by Rolis flasher.

Good luck~

Thanks~:)

[newcasper]

yes u r right sir
but i am not sure if he has flasher cable or not
and if he has a flashes of fls type or not
so I thought it would be easier if he used the same program and same cable and same type of flashes
and rolis is a very nice program and I like irt very very much
it solves a lot of problems

[dzonder]

I have Dejan box v1.04 Mbus cable, universal box etd. and I am yusing Windls and DTC-3 workshop with these file Nse8nx06.00b What you think can I yusing Rolis477 and where can I download

Thanks fot your sugestions;)

[newcasper]

so u must have flasher cable
and u can find rolis in the download section here in nokia free
then downlaod a 3210 flash file of .fls type not the flash file u have as it will not work
then reflash the phone

[chunkhead]

I just had a 3210 that I was flashing with Rolis, crash in the middle of flash! The error was due to low battery! (I forgot to check!) Anyway replaced with full battery and went to flash again, but... Got the error of "Phone tx=low...", then got "Pre Loader Init Error, Phone Ram Bad..."! After that, no matter what I did it wouldn't flash! After changing the Delay index from 5 to 1 I got "Sending boot loader..." but nothing would happen!

I got the phone to flash by setting the delay to 3, placing a piece of paper over the battery connections and when it said to power on, I pulled out the paper and connected the charger! Flash went in perfect and no problems since!

HOPE THIS HELPS!;)

[Romeo26222]

Originally posted by chunkhead
I just had a 3210 that I was flashing with Rolis, crash in the middle of flash! The error was due to low battery! (I forgot to check!) Anyway replaced with full battery and went to flash again, but... Got the error of "Phone tx=low...", then got "Pre Loader Init Error, Phone Ram Bad..."! After that, no matter what I did it wouldn't flash! After changing the Delay index from 5 to 1 I got "Sending boot loader..." but nothing would happen!

I got the phone to flash by setting the delay to 3, placing a piece of paper over the battery connections and when it said to power on, I pulled out the paper and connected the charger! Flash went in perfect and no problems since!

HOPE THIS HELPS!;)

Wow what ann idea you mean that if the phone can't be turned on I can use your method...gr8 but after connecting the charger should I press the power button or not??

[ryan_chong]

Hi again!

Hmm...most of the problems i hv when flashing a phone is the flasher cable connection.It would easily loose when u used it for a quite long time.:mad: Especially for 3210.....Gotta learn to make my own cable so everytime when it has been loosen i can make my own one... :P


Thanks~

[p.barker.3646]

no you dont need to press the power button the charger kind of does that for you

i have got a 3210 that i am trying to fix but when i try to flash it, it says "phone wont accept algorythem"????:confused:

i think it needs the eeprom reprogramming but i dont know how

can anyone help???

[ryan_chong]

Erm....i never face the problem u r having but i think it might be a small problem...Rolis will start to erase ur flash 1st b4 it'll start to flash...I still guessing tat might be a cable connection problem.(please coorect me if i am worng)So,try to clean up the tip on your phone with some methylated spirit.
Btw,what programs are u using to flash it?

Thanks!:)

[p.barker.3646]

i use rolis

i have tried lots of different flash files "borrowed" from different phones but none of them will run properly its like when you need to recalculate the faid and keeps resetting but it has full signal!!!

cannot get it to start flashing even after after cleaning the contacts!!

still it makes a nice paper weight!!!!:grin: :grin:

[chunkhead]

Well, I bought my cables as factory standard! So I know nothing about making my own or problems that occur when using them, nor do I care to learn! Hey, If it ain't broke, don't fix it! Anyway, NO you do not need to press the power button, and the method I described above I have only ever used once! So it's only a suggestion! Also the paper bit may/may not be relevant! But it's up to you! I'd love to here of this fixing someone elses problem though!

@ p.barker.3646: I have never seen this problem before but with regards to eeprom stuff, use Eeprom Tools v4.0! It will rebuild the eeprom among other things! But I doubt that's your problem!



;) ;) ;)

[p.barker.3646]

if i can ever get it to turn on and i put it onto logomanager etc, the imei and the production codes etc are all messed up!!!

i am using fully operational flashes from working phones and still no joy!!!!

i think that its beyond repair!!!

[chunkhead]

@p.barker.3646

If you can get it to turn on, try the following:

1)Connect phone via Mbus cable, power on and run Eeprom Tools v4.0
2)Uncheck "DTR On" and click "Read Info" (Magnifying Glass)
3)Allow to read phone info, click "Test"
4) If fail tests regarding Cobba, phone has hardware fault!, If return PPM or MCU fail, goto step 5.
5) Open Nfader By Al, select file (*.fls), uncheck "Fade on" and "Fade Off" if you do not want fading leds, check "kill CS/FAID" and click apply!
6) Flash newly saved file to phone, then...

Use Knok95
Quickset FAID, Reset User interface settings, Reset Full Factory Settings, Reset SP Locks, Set new IMEI, Use original IMEI, Quickset faid! In that order!;)