Nokia 8210 nsm-3 required attention

[zafarjanjua]

Hi to all Member


I am neweb in the field of gsm and I need help?

I tried to flash the 8210 gsm Nokia nsm-3 v5.29 by using nokia flasher 1.00b Dejan Kalgevic 2000

First I read the flash 100% and software creat the flash.out file in flasher directory of 1024.kb and then I write the partial flash file of 64.kb and after this my set become dead and could not “on” then I write the the same file flash out after renaming xxxx.fls hunder percent write but when I try to on the set but it could it could not start and screean blank . while software read the and write the mobile.


Kindly guide me

what mistake is done by me

next what step I take to recover the phone

is it possible to recover the phone

thanks allote

[coolmast3r]

hi
i think u should download a full flash (mcu+ppm) and flash it to your phone.do not use the 64kb file.i think that is the eeprom.
u can get a lot of flash files on the net.it should be around 1MB (in a zip file) of about 2MB in it's real size (unzipped).

[zafarjanjua]

kindly if it possible for u to upload or give me the link where i can download

thanks in advance

[mobile master]

Originally posted by coolmast3r
hi
i think u should download a full flash (mcu+ppm) and flash it to your phone.do not use the 64kb file.i think that is the eeprom.
u can get a lot of flash files on the net.it should be around 1MB (in a zip file) of about 2MB in it's real size (unzipped).

sir i also need the mcu + ppm file can u give me the link where i can downloand the file

[coolmast3r]

LOL man
u can find it here.
can u see the download section of this forum?
look at the upper right corner of the page and u're going to find it.
goto nokia >ppm+mcu file and select the phone model.
then u can downlaod it. the alphabet shows the language pack of the ppm.choose it.it is the same.all of them has englsh language pack.
or u can click here (http://nokiafree.org/forums/software.php) if u cant find the menu above.
HaHaHaHaHa..

[emul8d]

For newbie, it is advisable to use ROLIS Flasher coz Dejan is quiet difficult and the GUI is not friendly, but for me Dejan is still the best flasher!
Try this link the newest Rolis Flasher 4.79 (build 001)

http://nokiafree.org/forums/attachment.php?s=&postid=99532

Rolis flasher has a Dejan Interface, in case your using a Dejan box for flashing.

You can download 8210 MCU+PPM from the link given by coolmast3r, unzip the file to a specified folder
Run Rolis choose Nokia 8210 (nsm-3) then click Flash>Write, then browse for the file in which you unzipped the 8210 MCU+PPM pack
the flash location should start at 00200000 and ends at 00400000
then flash your phone.... (lightly click the power button don't power on)
After flashing in case contact service was shown flash that 64kb file that trashed your phone (8210 Virgin eeprom) on the address of 003D0000

Then if you have mbus connect that on any available com port...
On Rolis click Update FAID, Change IMEI, Update FAID, SP Factory Default, SFR and your done!

[zafarjanjua]

hi

sir

once again i am in problem

i have another nokia 8210 5.21 that was not in service i write the flash and but the later on when i try to connect the mbus with mobile and try to on the mobile. the message appear contact service and the message appear cmd not intiallize

kindly help me which procedure i adopt to erase and write new flash and set become service.


and also guide me whey it gone on contact service which mistake i do while 8210 5.29 which i repair first is working good


sorry for disturbancc

and thank in advance