PDA

View Full Version : contact service



jules
08-04-2002, 10:00 PM
hi
i have upgraded my 3210 to v6.00 but now i am getting contact service i have run test on eeprom 3.0 and message says ppm vadility test failed please repair the phone first
what do i do next
thnx jules :???: :???:

Visar Mato
09-04-2002, 07:41 AM
Try another ppm file and flash it/maybe the flash was no ok and than start nk calc F1 F2 F3 and will be ok/
Regards
Visar ;-)

jules
09-04-2002, 06:13 PM
Ooops
i used nk-calc using wrong cable now fone is dead will the fone work again if so wot do i do thx jules
helppp :???: :mad:

Visar Mato
09-04-2002, 06:21 PM
If you used the nk calc with wrong cable is not a problem/
Write mcu ppm
start nk calc F1 F2 F3
Regards
Visar

jules
09-04-2002, 08:45 PM
hi visa
run nk-calc pressed f1 f2 & f3 but keeps saying bad connection
thnx again jules

Visar Mato
09-04-2002, 09:13 PM
You need mbus cable/If that is mbus try it on another phone and if is ok,try to clean the pins at the phone maybe they are dirty/
You can work with nk calc and eeprom tools

:grin: :grin:

jules
14-04-2002, 12:34 AM
still read bad connection on nk calk,so used eeprom tool but now no network

Abe
14-04-2002, 02:43 AM
Visar Mato:
Please dont guide guys to do wrong things.....
F1 is to calculate Faid...so that is all you need after mcu+ppm updating....
Why you say to the guy to use F2 and F3?
F2 is to change IMEI and F3 is used to Unlock phone.......so please dont tell guys to do wrong things....
@Jules......
Flash the phone with good mcu and ppm file and then click on Flah autority ID button (first on the left)...
For flashing you need flasher cable and phone OFF and for FAID with eeprom tools you need MBUS CABLE TO COM PORT AND PHONE POWERED ON.....thats all......

Visar Mato
14-04-2002, 07:43 AM
I did many times that with rezults ans some times i need to do F1 F2 F3 to get network or i do update with Dejan box,this way i work on modified flash,and faid updater by tek doesn't work on my laptop/is a Compaq P3 850 Mhz and maybe that's the problem the speed,But when i do only F1 stll no network if i do F3 the phone resets and find network.
This is the way that i work.TESTED
And im not telling to others to do wrong things im trying to help them,thats why is this Great forum.
Regards
Visar
:smile: :smile:

gta18
18-04-2002, 01:44 PM
i have a 6 pin cable for 3210 but it automatically switches on if i connect the cable..


if i use my 4 pin ordinary cable for flashing. i always get a time out. form rolis.4.7x what should i use or do.??? thnx alot :)

Graham
18-04-2002, 08:12 PM
The 4 pin cable is a serial M or F bus and will unlock etc using one of the new unlock programes.
The 6 pin lead is a flasher cable for use with rolis flaser an others.
Pin one is the BTEMP connection this is the one that turns on the phone so you could try insulating this connection, Although I have not had this problem as my homemade lead only uses 5 connections.
Pin 1 is nearest to the top of the phone.

Regards Graham

boldi
19-04-2002, 08:53 PM
HI
gta18 for flashing with rollis 4.7x make sure u r using the lpt port
hope this helps
regards boldi

Osman
29-04-2002, 08:36 AM
http://nokiafree.org/forums/showthread.php?s=&postid=8571#post8571