PDA

View Full Version : flashing



nokia6210e_0527
15-05-2002, 08:46 PM
I've killed my 6210e by trying to flash the 64kb flash file for my version (05.27). Is there any way to repair this without a backup???thanks in advance.

NokDoc
15-05-2002, 08:51 PM
yep, just flash the same MCU version U had for that type and the phone will be normal again.

No use these 64k partial, no need anymore nowadays.

NokDoc

nokia6210e_0527
15-05-2002, 10:50 PM
Thank you for your help, please tell me Where I find my MCU version, and what is it? Thanks!

Zzzooommm
16-05-2002, 09:58 AM
Check here:

Napalm Homepage (http://napalm.all.at/nokia/flash/ppm.htm)
;)

nokia6210e_0527
16-05-2002, 06:02 PM
I tried flashing a backup file but it did not work my phone is still dead someone please help me!!!! Please tell me EXACTLY what to do thanks.

NokDoc
16-05-2002, 08:22 PM
Ok, so U flashed backup file.

A pity, that I think also had the eeprom area.
(if it was 4MB)
U will have to reset imei nr to Ur original.
U can do that with tool like bPhreaks eeprom tool.

Then after that U have to set the Faid, also with bPhreaks.
If the file was some 8% smaller then U only need the last option.

I hope that will work out.

NokDoc

Zzzooommm
17-05-2002, 12:14 AM
First, you must have MCU+PPM and Virgin Eeprom.
1 - write MCU+PPM in your phone with a flasher cable at Start Adress 00200000.
2 - write virgin eeprom at 005FA000
3 - with Knok and a Mbus cable, write the correct IMEI to the phone
4 - set Quick Faid calculation

nokia6210e_0527
17-05-2002, 11:15 AM
Thank you for your help I appreciate it very much. There is a problem though, my phone DOES NOT turn on at all, when I try flashing the data to it it does not work at all (I am using dejan flasher). Am I using a wrong boot.bin or f_loader.bin ? Thanks very much Zzzzzzzooom and Noc Doc.

Another problem since my phone does not turn on I cannot use any MBUS software (like eeprom tools by bphreaks since it says "Phone not connected")

Please could someone e-mail the correct boot.bin and f_loader.bin files I should be using to [email protected]

Another problem I do not know which PPM file to use and does it matter that the MCU file is for a 6210 05.26 and mine is a 05.27?

Adven
17-05-2002, 11:49 AM
Yes.... Go to the download area on NFee and get Rolis 477 or 478 from the Nokia section and use this to flash the phone.

Also if you want to keep 5.27 sotware version then you must flash that version to to phone, try this link for the MCU+PPM
http://www.flashes.online.pt/

Once its flashed to the phone it will start up and you can then use the Mbus again..
:)

Zzzooommm
17-05-2002, 02:37 PM
Instead using Dejan Flasher or any shell, try to flash your phone with Noki 7.3 (http://www.vilani.com/telefonos/marcas/nokia/programas/Noki_7.3.zip) . This soft work's under Windows support, and it's not necessary to config the loader's.
Then, flash your phone with MCU+PPM (all in one) for 6210 V.5.56 (http://flashes.ptisp.org/mcuppm/6210/6210_556_F.zip) at Start Address 200000.
After this, your phone will turn on and then you can use Mbus cable and Mbus software (Eeprom Tools or Knok, etc etc)

nokia6210e_0527
17-05-2002, 06:21 PM
IT WORKED!!!!!!!! THANKS U GUYS 4 ALL UR HELP!!!!!!! Ahhhh peace at last!!!