3310 flashing problem

[baraka42]

hello all.
3310 after changeing flash, reading with rolis 4.78
with good batterie and charger is pussed when ask for power on.

Nokia Mobile Info *---------------------------
Flash ID : 00200090,ST M28W160T, ALIAS_ID=00898890
-----------------------------------------------------------------------
Buffer too small even for MCU CHK test

nhm 5 110592 bytes done

NHM 5 do not send correctly flash block...

write flash to phone with rolis 4.78
Erased block started from 00200000 to 00360000
then stop [ with knock 95 stop at 68% ]

Nokia Mobile Info *---------------------------
Flash ID : 00200090,ST M28W160T, ALIAS_ID=00898890

flash read error reason may be

mobile disconnected.

batterie is empty.

cable is not good.

also try to erase the whole flash with knock 95.

then write with rolis, no result.

sorry for my bad english.

thanks in advance.

:mad: :mad: :mad: :mad:

[wwanthony]

Same happened to me.
I erased the full flash with knok and kept trying to flash my originaly read flash.

I noticed when i pluged the charger in for a second when asked to power on it wouldnt work, but if i held it in for 4 or 5 seconds longer then thats when it worked.

Then when the original flash was complete, I just flashed in my modded one and it worked fine.

So theres no set thing to do, just persistance, and i took out the battery a few times and made sure the cable was fine and in place correctly, and kept trying to flash it. Took about 20mins of trying when it decided to work.

Good Luck!

[iko]

When you have problem with Rolis xxx
try
Knok 2K3 Unlocker/Flasher

[chunkhead]

Nah, don't blame Rolis! It's flawless except for the 5210! Rolis will erase the flash anyway, just select the flash (Whole Flash) and when it asks for power on, plug in charger and leave it in! Make sure there is at least some power in the battery beforehand though!!! Also clean contacts on phone and cable! Have you used the cable before to flash?

[baraka42]

@ iko,

i had try with all knok ver. all have same massage

"Cannot prepare phone" and 2k3 "cable no conectado"

@ chunkhead,

i don't blame rolis . it's my first choic. some time i have get result
by erase flash by knok and write by rolis.

@ wwanthony.

you min after pluged the charger in and held it in for 4 or 5 seconds . then remove charger ?

my main problem is flash erase only 68%. why it stop at 68 %.

is there any mistake in change flash ic ?

pls. read carefuly cause of my bad english.

thanks all for his time to reply me.

i need more help.

:) :) :) :)

[iko]

@chunkhead

I don`t blame rolis. WHY?
Because I always useful this software *_rolis v4.79b1-before 4.78b6_* when I need flash phone.
ALWAYS @chunkhead always.
except 2100,3610_
This is the GOOD software.

Sometime some phone maybe have problem
and he rolis and Lead`s kNok-Phoenix b1 is writing:
Seems,that loader can not erase whole flash!
Nokia Flasher v1.00b ba Dejan similar.
/_sometime-not always Knok2K3 successful is solving; why:???_/

For new flas I use ROLIS again and again.
Successful am flash more than 70 phone with ROLIS without problem.

@baraka42

first check cable(Flasher)!
or Maybe you have problem with Current CPU speed?

Try:
Rolis 4.79b1 with W.T. files nhm5ny05.590 MCU and PPM also
*or the newer version whom you are possessing*
Load MCU - Load PPM and Flash

www.gengheraenga.net
*and download this file*

[wwanthony]

Hi baraka42,
When I held the charger when asked to power on for one second then removed it, it would start the flashing process but would stop after a second with an error. When i held it in for 4 or 5 seconds it started and didnt stop, or it may be better to do as chunkhead says and leave the charger plugged in.

I think if you have tried to erase the full flash many times over without success, using Knok and Rolis then it must be some sort of hardware fault, be it the cable or something on the phone.

As chunkhead says above clean the cable contacts, an ear bud stick thingy works, use a spinning action.

[chunkhead]

@iko:


When you have problem with Rolis xxx

You said you had a problem with Rolis! I said, "Don't blame Rolis"! Rolis does not have problems, it's flawless except for 5210!:D

@Baraka42:
Like I said before, your software is probably not at fault! But... check to make sure that the correct LPT port is selected in settings and also try different Delay Index settings! Clean ALL hardware, especially the phone contacts and it probably won't hurt to do the Meths dip!!! ;)

[baraka42]

thanks all,

my system;cable;battere. charger ..all work ok with other 3310.

i will post after reples one more flash.

thanks again all.

S4ME