wintesla software

[downunder]

i'm using a cracked version of wintesla and have been able to tune and align, reset etc older model phones ok, but if i try to connect a 6210 or 6250 wintesla says no deskey found, have tried reloading dll files and recopying crack software to wintesla but no luck

any ideas.....

[Shidoshi]

try another program :)

[kid_rock]

try another program....

heres the site... wintesla_6.03

www.ed2k.com.ph

[downunder]

i am using wintesla_6.03 from this site with the cracks, but
it seems the later phone dll files dont let this version work.

as far as i am aware this is the only program that allows the phone to be tuned (RX & TX)... is this correct

[Shidoshi]

Hmm...

What do you mean by RX & TX?

-Dave

[downunder]

RX -- reception levels, used to unable phone PLLs and Auto gain
control to adjust, so phone transmits correctly on whatever
channel is used. helps eliminate drift/noise etc.

TX -- Transmission levels. the output power of the power amp for
each level, 5 - 15 has to be correct or cell site will drop call.

[Shidoshi]

Hmm...

Fair Dinkum...
I think I understand. Thanks for the info mate.

Hey, where abouts from Oz are ya from?


-Dave

[KnOeFz]

@downunder:

Maybe Phoenix, the replacement of wintesla for dct4 types can interest you ?? Here's some info about it (hold on, it's a long piece of text) scroll down for d/l links :D Don't think it's for dct3 though.

-------------------------------------------
Phoenix Service Sw 3.76.002
PHOENIX SERVICE SW 3.76.002 FOR
NHL-2*/4*, NHM-4*/7*/8*, NPE-4*, NPL-1*, NPM-9*, NSB-8* AND NSM-9*

Introduction

New version 3.76.002 of DCT-4 generation Test and Service Software is available for
NHL-2*/4*, NHM-4*/7*/8*, NPE-4* , NPL-1*, NPM-9*, NSB-8* and NSM-9* phones.

The name of the package has been changed to Phoenix Service Software A2

Please see product specific Service Bulletins for instructions .

Service SW installation package and product specific service bulletins are available from the Nokia Partner Website. The SW is also available on CD ROM.

This installation package contains following components:

- Phoenix Service Software
- PKD-1 / FLS-4 Dongle Drivers
- Product specific information for the Faultlogger

After installing Phoenix Service Software version 3.76.002, please install latest product specific data package DO NOT USE OLD DATA PACKAGES.

In order to make the Service Software and tools usable with the NHL-2*/4*, NHM-4*/7*/8*, NPE-4* , NPL-1*, NPM-9*, NSB-8* and NSM-9* phones, you need to install following update packages.

1. Latest Phoenix Service Software ( 3.76.002 or newer)
2. Phone model specific Phoenix Data Package
3. Latest Flash Update Package for FPS-8/FLS-4 (v 2.06.001 or newer)
4. JBV-1 Software Update (When necessary)

For details of installing each package, please refer to phone model specific Service Manuals and Service Bulletins concerning each mentioned update package.







Changes from v 3.72.002 to 3.76.002


New Features
• Support for NHL-4, NSB-8 and NSM-9
• SIM-Lock Status UI component tells the service technician if the product is SIM-locked
• Phonebook Voice Tags saving disabled – See Product specific Service Bulletins !

Updated Features & Error Corrections
• Ambient Light Detector Calibration (NHL-2*)
• Default settings changed for Proximity Detector Calibration - component (NHL-2*)
• Improvements to FPS-8 / FLS-4 Flashing speed
• Phone wakeup indication after flashing support
• Other product types than the one described in productcode.ini files are not shown in manual selection / product -dialog.
• Added warning dialog if setting are not selected.
• FLS-4 warning dialogs are changed so that they are modal.
• Default timeout after flashing increased from 0.5s to 3s.
• Support for flashing NHL-4* Content packages
• The product code is automatically written to the phone when rebuilding IMEI or ESN.
• When ESN is being rebuilt, the product code is only written to the phone if a PKD-1CS dongle is attached.
• Product Profile UI reacts on changes in the connection state
• Rx Band Filter Calibration default signal values and help files update
• Improvements to TX I/Q tuning
• Support for unicode file names.
• Add / remove file - feature to NHL-2* usersettings component
• Improvements to Camera Control (NHL-2N*)
• Fault Log long SW version string reading corrected
• Improvements to FPS-8C flashing with Win 98
• Improvements to Label Printing
• PPC Counter support updated
• WAP Settings saving improvements
• Backup/restoring the setting files improvement for NHL-2*
• Backup/restore handles UNICODE name endianess correctly.(NHL-2*)
• Photo Album settings backup is performed twice (NHL-2)
• Product Serial Number error message corrected
• Energy Management Calibration error when closing dialog fixed





Known Errors
• Audio Routing and Test Signals for NHL-4 not included in the release
• Fault Log info for (NPE-4) is disabled.
• Security Settings can’t be restored.
• Phonebook: Voice Tags can't be saved at all

Assemblies Affected

All NHL-2*/4*, NHM-4*/7*/8*, NPE-4* , NPL-1*, NPM-9*, NSB-8* and NSM-9* products


Implementation Data

Date August 2002
SW A2 03.76.002
IMEI -
Implemented 16 August 2002


Parts Required

NAME CODE
PHOENIX SERVICE SOFTWARE A2 CD 0774286



Special Equipment:

- Phoenix Service Software v 3.72.002
- Latest Product Specific Phoenix Data Package (NHM-7 Data Package 7.0)DO NOT USE OLD DATAPACKAGES
- Flash Update Package 2.06.001 for FPS-8* and FLS-4*
- PKD-1 Dongle
- Activated Flash Prommer FPS-8* OR FLS-4* POS Flash Dongle
- Phone model specific service tools


Procedure

1. Download phoenix_service_sw_a2_03_76_002..exe – application file to your computer (eg C:\TEMP)
2. Close all other programs
3. Run phoenix_service_sw_a2_03_76_002..exe and follow instructions on the screen to install Phoenix Service Software.

Tuning Instruction

None

--------------

Downloads:


3.72 uncracked (needs pdk1) (http://ptisp.com/~skyn3t/zip/phoenix3.72.rar)

3.30 cracked (http://ptisp.com/~skyn3t/zip/winphoenix.zip)

Can't help you with using the soft was I have no experience in doing this :)

Have fun :D

-=K=-

[nase ck]

here it is solution...1st thing u should install software support like NHM5 or NPE6..this software not crack...so if u run your wintesla the msg illegal operation will appear or can't find deskkey drive or something like that.
2nd try find cracked dll like nsek13. if u found that cracked dll please copy that file to win/sys
3rd. in dir. wintesla try looking for tesla.ini...after u found it..go to [NHM5] or [NPE6] . look at UserInterface=NHM5
Functionality=NHM5. so u have chage this to NSKE13(cracked dll) or other cracked dll.

i think this solution could be success...try it....tg