6310i Security Code - it isn't default

[Rascalator]

When I put a PAYG sim into the 6310i I used to have on contract with T-Mob is says 'Security Code'. I have tried the usual 12345 but is doesn't like it. I have run the code unlocker and it says that the phone is not restricted.

How can I default the Security code?

Hope someone can help.

Cheers, JohnO.

[cprafferty]

This software will allow you to reset the code to 12345 with a datacable.

[Rascalator]

HI, thanks for the response - the software seems to want MSCOMM.

I have tried this on XP Pro and and old Win98 machine and no joy - do I need more modules? I have just seen another of your post referring to Visual Basic 6 - I'll hunt for the runtimes.

I only have a data cable for the 6310 - do I need a 'special' cable?

I have load VB6SP5 runtime and still no job withe the FBUS.EXE program you posted. I'm looking for even more help.

Cheers.

[cprafferty]

Try this one.

[Rascalator]

Thanks...The software runs apparently fine. When I connect DLR-3P cable and mains adapter I get 'ERROR: Phone does not answer!' when I click reset security code.
------------- From Help ---------------
Solution 1:
1.Connect charger to phone, with battery & MBus cable
2.Contact Service is show, power off phone!
3.Phone gets in changing mode (retry if not)
Press Unlock!
>>>> I don't understand Contact Service is show <<<<
Solution 2:
Connect Btemp (pin next to GND pin on battery) to
GND, turn ON phone and phone will be in Test mode.
Or connect BSI (pin next to "+" pin on battery) to
GND, turn ON phone and phone will be in Local mode.
>>>> I don't know which is the ground pin, is it -ve on the actual battery or two of the seven gold connectors where the data cable connects.

Signed: An absolute novice.

[Abe]

Dlr3 is a MODEM cable,so u will need a DATA cable for playing with MBUS and FBUS commands.Usually data cables come with AUTO FBUS/MBUS switcher,but u can find also with MANULA FBUS/MBUS switcher.Both are same.

[Rascalator]

Thanks Abe.

[Rascalator]

My firmware is:
V 5.22
15-11-02
NPL-1
(c) NMP

Will a cable clear the above security code? Suggestions for a cost effective supplier - I'll only need it once.

Cheer John

[Rascalator]

My firmware is:
V5.22
15-11-02
NPL-1
(c) NMP.

If I get a proper cable will it work with my firmware level?
Where would you recommend a cable for just the one use? I don't want to spend a fortune for a single use.

Cheers.

[Rascalator]

[My firmware is:
V5.22
15-11-02
NPL-1
(c) NMP.

If I get a proper cable will it work with my firmware level?
Where would you recommend a cable for just the one use? I don't want to spend a fortune for a single use.

Cheers.
----
QUOTE=Rascalator]Thanks...The software runs apparently fine. When I connect DLR-3P cable and mains adapter I get 'ERROR: Phone does not answer!' when I click reset security code.
------------- From Help ---------------
Solution 1:
1.Connect charger to phone, with battery & MBus cable
2.Contact Service is show, power off phone!
3.Phone gets in changing mode (retry if not)
Press Unlock!
>>>> I don't understand Contact Service is show <<<<
Solution 2:
Connect Btemp (pin next to GND pin on battery) to
GND, turn ON phone and phone will be in Test mode.
Or connect BSI (pin next to "+" pin on battery) to
GND, turn ON phone and phone will be in Local mode.
>>>> I don't know which is the ground pin, is it -ve on the actual battery or two of the seven gold connectors where the data cable connects.

Signed: An absolute novice.[/QUOTE]