6600 -BT-> PC -> Internet now works!!!

[grave]

How-To - Internet over PC with 6600 (wap2)

i tried the posted link and did what was written there and i just got it to run! it means my 6600 connects to my pc and CAN use its internet connection!
tried it with the nokia standard browser, opera and wirelessirc1.8!

my system is windows xp and i just followed the instructions on http://www.cs.helsinki.fi/u/mraento/symbian/bt-ap.html
but ill try to write step-by-step instructions :)

1. Deactivate all the Checkboxes in mRouter (at least the ones of the Bluetooth COM ports)
2. Goto Bluetooth settings and Deactivate everything else in Local services than Bluetooth serial port, note the com port you set as bluetooth serial port
3. Goto Phone and Modem options, go to "Modems" add a new one, activate "I will select it from a list"
4. choose "Communications cable between 2 Computers" from the list (in Standard Modem Types)
5. Select the COM port from step3
6. in the modem settings set maximum port speed to 115200
7. goto Network Connections and create a new connection (wizard)
8. Select “Set up an advanced connection” -> Next
9. “Accept incoming connections” -> Next
10. Check the “Communications cable between two computers” -> Next
11. Do not allow VPN connections ->
12. select a username you want to give access to your pc over Bluetooth (that’s the username you will set on the phone later)
13. in the settings of that connection go to Network select TCP/IP -> Settings
14. set the IP range to something like 10.0.2.2-10.0.2.254 or, what you like
15. Remove Internet Connection Sharing from all interfaces
16. run cmd.exe and enter the following commands:


netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private

“YOUR LAN INTERFACE NAME” has to be replaced with the name of the interface connected to the internet
the “Internal” of the last line depends on the language of your windows (e.g. german: “Intern”)

17. if there is a "Bluetooth Network" connection in Network Connections delete it

your pc should now be set correctly :)

go on with your 6600:
1. Download gnubox6600.SIS (http://nokiafree.org/forums/attachment.php?attachmentid=12499), attached to this post (or download here (http://www.cs.helsinki.fi/u/mraento/symbian/gnubox6600.SIS)) and install it on your phone
2. Create a new Access Point on the phone (Setting|Connection|Access points|New access point|Use default settings).
3. Use the following settings for it:

a. Name: Bt. The name is important, the software will look for it.
b. Data Bearer: GSM data
c. Dial-up number: e.g. 2222. It doesn't matter what you have here as long as it's not empty
d. Username: the username you gave access to the incoming connection earlier
e. Promp password: No
f. Password: password for the user on Windows
g. Authentication: Normal
h. Advanced Settings: Use Login Script Yes
i. Advanced Settings: Login Script


CHARMAP [windows-1252]
LOOP 10
{
SEND "CLIENT"+<0x0d>
WAIT 3
{
"SERVER" OK
}
}
EXIT KErrNoAnswer$

OK:
EXIT

be careful that you get it exactly as show here, including linebreaks. You could save it to a file, send to the phone and copy-paste to the settings.
j. Advanced Settings: Use PPP Compression Yes
4. run the program you installed at step1 (gnubox)
5. inside gnubox: Options-> 2box Direct -> Bluetooth, select your computer, leave gnubox running in background
6. run the nokia wml browser select "Bt" as access point and connect :D

thats all i did... sounds much now but i think it was worth the time i needed :)
i hope i could help you guys set this thing up
btw i just streamed a live tv to my 6600 over bluetooth with real helix :)
-----
grave :rolleyes:

sorry for posting twice :) just wanted to be sure everyone reads it
some parts of this how-to were just ripped from http://www.cs.helsinki.fi/u/mraento/symbian/bt-ap.html and following
just fyi not to get beaten by those who really found out how to do it

btw, im off from 21.5. till 28.5.04, so i cant answer messages, but ill answer all your questions (pm) after that ;)

Edited by GeeZuZz: I have uploaded and attached the gnubox6600.sis application to this post (zipped).

[tzeonn]

nice.

i will make tis a sticky 1st.

if tis works, i will get permission to place tis on the faqs section.

thanx!

[Iceman5]

when i get to

netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full

i get a message saying that NAT has to be installed first!!

what do i do...? and where do i find the lan interface name btw??

plz help me! the rest is working fine tho

[grave]

i get a message saying that NAT has to be installed first!!
-> type "netsh routing ip nat install" first


and where do i find the lan interface name btw??
-> open Network Connections and take the name from the list

[Iceman5]

type "netsh routing ip nat install" first
I did! thats the weird part... after that the comp worked for a sec or two then it gave me a new type line... take a look at the screeny. it ses NAT has to be installed first


open Network Connections and take the name from the list
its one of these right? which one?? i tried them both but still got the NAT message. lokal tilkobling = local connection

If u cant view the uploads heres the links:
cmd (http://nokiafree.org/forums/attachment.php?attachmentid=12491)
network connections (http://nokiafree.org/forums/attachment.php?attachmentid=12492)

[grave]

maybe try doing the nat thing with winroute like i have it now, not that easy with just 3 lines but it may work better
dont know the exact settings but i think the helpfile may help

so, i'm now off for one week, sorry guys

grave

[c00per]

arghhhh I feel like a real nOOb. Where can I find the "YOUR LAN INTERFACE NAME" looked it up and filled it in. But in the cmd box it gave an error!!!

thnx

[edit]: nevermind, I've found it, my network name was too long.

bye all and good luck

[c00per]

Hmm I'm at the step of gnubox and I made the accesspoint. Gnubox works, but I still get a dns error. Somehow I think it has something to do with my bluetooth network connexion which i can not delete from my pc.

[c00per]

hmmmm, with Netfront I select the Bt connection and in the progress bar i get 'scanned script' and after a while completed. But then I have to choose a connection again :-?

hope people can figure it out.

bye all and good luck

[ducklegsux]

hmm i got through except the "netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private" i am getting errors while at this stage,it is telling me that
The interface ''Internal'' does not exist.
An interface with this name is not registered with the router.
i am using win2K by the way and i am on cable so the lan interface part do i put the newly created connection name or my default lan connection name?anyway i have tried both but they fail,any help would be deeply appreciated

[c00per]

You have to use your Lan connection name But don't make it too long or else it will give an error too. I renamed mine to WIFI :)

[Iceman5]

ok everything seems to work but when i connect using the accesspoint it ses wrong phone number!!

i know theres a connection there coz i can see the gprs bubble (just like when u make or recive a call) and my pc screen goes weird when my phone is close to it... u know what i mean. but this phone number thing makes it not work!

i put in 2222 as phone number btw. just like the tut sed

Edit: ok i changed the number to 1111 and now it just ses "ERROR invalid DNS value spevified"

[kandissa]

I am on 56k dial-up and I do not seem to find my lan interface name from Network Connections. My Network Connections shows three headings:

Dial-up
Incoming
Wizard

Dial-up lists the name of two dial-up ISP connections I use.
Incoming shows the new connection that I just created following this guide.
Wizard is the old WinXP New Connection thing.

Somebody help me please.Please.

[AlmostRandom]

Use one of the dial ups

[Kniteforce]

:) it works !
Using a DCHP Windows XP client / Sitecom BT dongle
but didn't really understand the netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full command. But it works, so thanks :)

[c00per]

can someone explain step 15 and 17. Where at step 17 i can not delete the bluetooth netwok :-?

thnx people


COOOOOOOOOOOOOOOL it works

it works, its alive I tell you ALIVE

[c00per]

guys i've used this manual, cause it has got a proxy port configuration as well. Without it i cant get it to work. With the proxy program it works.

http://www.allaboutsymbian.com/forum/showthread.php?p=169763#post169763 I hope this is okay with the mods. It really works this time

[jaron]

www.cs.helsinki.fi seems to be down, can anyone else host the .sis and pages based there?

The main site loads, but the actual links given above aren't working.

[GeeZuZz]

www.cs.helsinki.fi seems to be down, can anyone else host the .sis and pages based there?

I have edited the first post and attached the file :)

[AlmostRandom]

I had a problem which I coulnt figure out for ages but finally have it working now too.

My problem was when trying to do the accept incoming connections in step 9, it said it couldnt start routing and remote access. The solution to this is to install client for microsoft networks.

Go to:

My Computer -> My Network Places -> View Network connections

right click on Local Area Connection -> Properties

Install -> Cleint -> Add

Cleint for Microsoft Networks


Also when doing the adding your 6600 access point settings, remember you can add settings in the PC suite.
This makes it a lot easier as you can just copy and paste the script in part 3i:


Connect to the phone to mrouter in the usual way
(you will have disable the incoming connection temporily and enable your mrouter com port):


- network connections -> Incomming connections
right click -> properties
uncheck "communications cable between two computers"

- right click on mrouter and re-enable your normal com-port
connect in normal way

- pc suite -> settings wizzard -> next
change phone settings manually -> Remote connections -> add new

- Add the connection as stated in part 3
Note the data type you want is the bottom one (HSCSD).

- Now disable the com port in mrouter again
and re-enable the incomming connections check box just disabled


Note you will still have to enter the password on the phone.

Hope this helps.
Good luck ;)

[Optimisten]

Dooh, figured ou the problem - i was doing it all wrong. Now i'm back on track, but it still does not work at all.

The GNUbox works and the screen turns blue, but i get: Could not connect, check your settings error, when trying to connect.

[AkiraYuki]

For those of you having trouble deleting the "Bluetooth Network" Icon, you can't. You just have to right click the icon and select "Disable"

[hacksore]

anyone have any ideas on how to get this to work on a mac?

are these instructions using the bundled software for pc?

[AlmostRandom]

This was working perfectly... until I tried to use agile messager. I loaded it, and it said there was a new version avaiable which it downloaded and installed automatically.

And then it didnt work. I uninstalled agile. still didnt work. I then went through the whole list again doing all from scratch. alas, no joy.

Any suggestions... please... ?

[Kniteforce]

This was working perfectly... until I tried to use agile messager. I loaded it, and it said there was a new version avaiable which it downloaded and installed automatically.

And then it didnt work. I uninstalled agile. still didnt work. I then went through the whole list again doing all from scratch. alas, no joy.

Any suggestions... please... ?

same problem here, but i didn't choose download new but agile worked fine. But when i tried it another day it suddenly stopped working. I was getting app closed. But today i removed it then i installed the new version from the official website (6600 version) and it worked again via 6600 - BT - internet.

[silence]

Will doing this break anything on the phone in regards to using it as intended with the network provider or is it an additional connection?

[csousa]

" 16. run cmd.exe and enter the following commands: "
"netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full"

can't do that because i'm using an usb ADSL connection, apears as a dial-up connection. Any ideas to help me on this step?

[tzeonn]

" 16. run cmd.exe and enter the following commands: "
"netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full"

can't do that because i'm using an usb ADSL connection, apears as a dial-up connection. Any ideas to help me on this step?

u mean, bluetooth is shown as a network?

try going to device manager, under the network tab, disable the bt. my bt dongle worked this way.

[csousa]

Sorry for the english.. i'm portuguese so i can't express myself very well.
I'll try to explain better:
Whem a try to make this: "netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full"; it gives me an error, saying:
"The interface 'Alcatel' does not exist.
An interface with this name is not registered with the router."
Alcatel is the connection to my internet. so how can i do that....
Here a picture of my network connections:
http://cosmos.oninetspeed.pt/MICHEL/ok.jpg

[whitey420]

omg I gotta go get a bluetooth port for my computer today and do this :-o !!!


also I'm wondering if my my mother's 7250i can use my PC internet connection if I get bluetooth add-on for 7250i?
thanks!

[Optimisten]

also I'm wondering if my my mother's 7250i can use my PC internet connection if I get bluetooth add-on for 7250i?
thanks!

It will NOT be able to use the BT internet connection.

For this to work you got to have the GnuBOX installed on your phone, and it's a Symbian programmed application - get my point:)?

[whitey420]

well Its working for my 6600 :D, but I can't use agile messenger, can anyone else?

[Optimisten]

well Its working for my 6600 :D, but I can't use agile messenger, can anyone else?

You B***C - i have used like 4 days and it still won't work.

You go to hell - you go to hell and you die;)

[whitey420]

It will NOT be able to use the BT internet connection.

For this to work you got to have the GnuBOX installed on your phone, and it's a Symbian programmed application - get my point:)?


99.9% of phones you dont need GnuBOX nokia didnt be idiots make bluetooth internet nearly impossible like in 6600

[whitey420]

You B***C - i have used like 4 days and it still won't work.

You go to hell - you go to hell and you die;)


Try using that method http://www.allaboutsymbian.com/forum/showthread.php?p=169763#post169763

:)
its working fine here

[tzeonn]

You B***C - i have used like 4 days and it still won't work.

You go to hell - you go to hell and you die;)

Pls, respect others.

[whitey420]

he's been watching too much South Park :lol:

[whitey420]

damn i want agile to work!!!! :sad:

it'd be so good, multi-player games and msn at same time :sad:

[whitey420]

this proxy program isn’t good, people scan IP ranges for open proxies and use your computer IP to keep them anonymous whiles doing illegal activities like fraud...

[Optimisten]

Pls, respect others.

I'm sorry if you cannot catch my sense of humor. I ment no harm..


Damnit! I get TCP error when trying to access a website:(

[d0gi]

I got it working with Windows XP, altough I was hoping it'd work with linux because now I have to connect through my laptop.. Well, anyway I'm not sure if this helps but I set my DNS servers manually in the phone (the same place where you define the proxy) and no need for proxy here.

Agiler Messenger & Wireless IRC work without problems :)

[Optimisten]

I got it working with Windows XP, altough I was hoping it'd work with linux because now I have to connect through my laptop.. Well, anyway I'm not sure if this helps but I set my DNS servers manually in the phone (the same place where you define the proxy) and no need for proxy here.

Agiler Messenger & Wireless IRC work without problems :)


Well now i tried this, and now i actually can see i get connection with the computer. But it says:

<Ikke-godkendt-bruger> >> <Not-reconized-user> (or something like that)

And that crap - i'm 100% sure i wrote the right username and password.
There is one thing; when i open the properties for users in the incomming connections dialog - the password (in *'s) is much longer than the password i added for that user. Is that for securerity reasons, or am i doing something wrong?

[PhreeZ]

is anyone else experiencing weaker signal strength after having installed gnubox? :-?

i've installed the 7650 version on my ngage, and i get no reception in my basement anymore! :sad:

[a_dude]

lol...why the hell u installed gnubox for the ngage?!?!?!

the ngage already has the net via bluetooth easily...readup man....

far out...

[Sawyer2003]

i always have " no gateway reply" with 6600 browser
:-?

[PhreeZ]

lol...why the hell u installed gnubox for the ngage?!?!?!

the ngage already has the net via bluetooth easily...readup man....

far out...

i use gnubox because it is far superior to the other BT -> Internet method.

firstly it allows me to use the built in wap browser, removing the need for some 3rd party browser. :-P

secondly, the method of initiating the connection is much more convenient. i can automatically pair up with my PC using gnubox instead of having to go to my pc and manually pair up. ;)

thirdly, just because i want to! :evil:

hell that's why i installed gnubox on the ngage! :-x

after all gnubox was originally developed for S60 v6.1 phones, and it was only recently modified to work with v7.0. read up man :lol:

[csousa]

hi there, for the people that use the proxy solution, and can't use the messenger aplication. Use this page http://start.e-messenger.net/mobile/ to acess the MSN messenger through a mobile web browser :rolleyes:

[Optimisten]

When i try to connect with my computer (i used both the proxy thing and my DNS) the incomming connections changes to <Not known user> or something like that, on danish; Ikke godkendt bruger.

Why is that? I'm 100% sure i typed in the right password - made it simple as hell!

Please help

[AlmostRandom]

You probably all realised this anyways, but once you have run gnuBox once and got it working, the settings are saved to the phone. This means you dont have to run gnuBox when you want to use it.

In fact you dont need to run it ever again really, unless you make changes to your access points or something like that.

--



When i try to connect with my computer (i used both the proxy thing and my DNS) the incomming connections changes to <Not known user> or something like that, on danish; Ikke godkendt bruger.

silly question but you are sure that the user is ticked to be allowed to use the incomming connection?

[Optimisten]

silly question but you are sure that the user is ticked to be allowed to use the incomming connection?

I'm a 100% sure - I have all my users ticked to be allowed to use it.
That's why i think its wierd.

[Gray]

My ip adress changes everytime I make a connection. (adsl-->proxy-way ;) )
So I have to Type the Ip-adress over and over again when I want to make connection.
Is there a way to have a solid IP?
Greetz

[Sawyer2003]

Gray : Just enter 10.0.0.1 instead of your Ip adress

[ash007]

hey guys can u tell me how to make my 6600 connect to internet thanx. i got some diff way of getin on the net. my computer is part of a wireless network n my sis computer is the host computer which has the boradband modem n shares the internet to all the wirelss devices. i jus wana know how to setup this stuff with the shared internet connection.thanx.

[whitey420]

OH my god!! I uninstalled my virus scanner and shut down firewall and its working without proxies :oops: :D

try this if u cant get workin!

agile messenger yay :D


ThANKS GUYZ!!

[ogie01]

hey guys, i cant understand, can you enlighten me?!? :-o
1. your using the connection on the pc (isp server) to browse the net using the 6600 or you using the connection on the 6600 (i.e. gprs) to browse using the pc? because from this " tried the posted link and did what was written there and i just got it to run! it means my 6600 connects to my pc and CAN use its internet connection! tried it with the nokia standard browser, opera and wirelessirc1.8! (quoted from grave)" does it means your using the connection of the pc (isp server). :-?

2. can you use irda insted of bt? and does this only work for windows xp? how about other windows e.g. windowsME?

thanx....

[cyclonefr]

somebody help me : im in wireless im connected to a WIFI ROUTER (so im in infrastructure) and i can get it to work: im sure this is because i dont know what to put instead of "YOUR PRIVATE LAN NAME"
someone help me or tell me it doesnt work with ICS

[6600newbie]

ok i tried evrythin as in d tut, but stil cant get itto work! :( ok guide me thru this plz, wen i start up gnubox (after setting up al the other parameters on d pc n mobile) do i create a bt serial port wit my mobile? i tried both ways stil don work. another thing, wen i say netsh routin ip nat add interface <my dialup connection name> full it says the connection name is not registered. im supposed to use d dialup conn name rite? another thing, wen i tried it once, d incoming call (using the comm cable setting) did set up for about a second or two, but then it went off, n then it hasnt worked since. sumbudy plz help me thru this, sumbdy whos actually gotten this thing to work. u can add me to yo msn <hotmale_17_> thts d id. thx a lot.

[AlmostRandom]

somebody help me : im in wireless im connected to a WIFI ROUTER (so im in infrastructure) and i can get it to work: im sure this is because i dont know what to put instead of "YOUR PRIVATE LAN NAME"
someone help me or tell me it doesnt work with ICS

assuming your on windows xp
go to start, run
type cmd
type ipconfig

it will list a some items
one of them will start with "Ethernet adapter" and will be folled by the name you need to type for "YOUR PRIVATE LAN NAME"

[6600newbie]

ok now evrythin seems to be working good but one slight problem, the mobile still cant access the net!!! the pcs acceptin incoming connections and the bt serial ports created automatically wen sum prog from the mobile requests to access the net, but thats it, the mobile connects to the pc n it just stay that way, no data actually goes thru that connection, wat cud i be doing wrong??

[AlmostRandom]

ok now evrythin seems to be working good but one slight problem, the mobile still cant access the net!!! .....

This sounds like somethings wrong with the routing commmands entered - as the phone is connecting to the pc but external packets arent being sent to the phone. Try reseting them like this



netsh routing ip nat uninstall
netsh routing ip reset


and then re-enetering the initial three commands



netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private

[6600newbie]

This sounds like somethings wrong with the routing commmands entered - as the phone is connecting to the pc but external packets arent being sent to the phone. Try reseting them like this



netsh routing ip nat uninstall
netsh routing ip reset


and then re-enetering the initial three commands



netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private




ok i think thats where the problem lies, cuz apart from that step i did evrything correct. just one problem tho, wat xactly do i giv in as my lan interface name cuz i dont hav an ethernet adapter, i use dialup, i tried using my dialup connection name but it says this interface is not registered with the router and tht it does not exist. now wat? :-s

[whitey420]

omg now i format phone i cant get it working again!

i try to connect it says connecting via bt then the nokia wap browser minimizes on its own :-? :-?

no connection seems to be coming to my PC from Bluetooth when i try goin on WAP or agile messenger either :-?

[whitey420]

never mind got it working again :)

[hakbar1]

Very Nice Topics Thanks yara

[rlachenal]

Still can't get it to work without running a proxy on XP.

Could someone who has this thing working with Agile Messenger without a proxy please post their routing table here? (Just open a command window (cmd.exe) and run ROUTE PRINT).

Thanks in advance.

[whitey420]

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

C:\Documents and Settings\hidden>ROUTE PRINT
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
numer codes here(privacy?) ...... MAC Bridge Miniport - Packet Scheduler Miniport
numer codes here(privacy?)...... WAN (PPP/SLIP) Interface
numer codes here(privacy?) ...... USB Cable Modem 351000 #2 - Packet Scheduler
Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 82.1.63.254 82.1.63.* 30
82.1.63.0 255.255.255.0 82.1.63.* 82.1.63.* 30
82.1.63.1 255.255.255.255 127.0.0.1 127.0.0.1 50
82.1.63.8 255.255.255.255 82.1.63.1 82.1.63.1 1
82.1.63.* 255.255.255.255 127.0.0.1 127.0.0.1 30
82.255.255.255 255.255.255.255 82.1.63.* 82.1.63.* 30
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
169.254.0.0 255.255.0.0 169.254.55.66 169.254.55.66 10
169.254.55.66 255.255.255.255 127.0.0.1 127.0.0.1 10
169.254.255.255 255.255.255.255 169.254.55.66 169.254.55.66 10
224.0.0.0 240.0.0.0 82.1.63.* 82.1.63.* 30
224.0.0.0 240.0.0.0 169.254.55.66 169.254.55.66 10
255.255.255.255 255.255.255.255 82.1.63.* 82.1.63.* 1
255.255.255.255 255.255.255.255 169.254.55.66 169.254.55.66 1
Default Gateway: 82.1.63.254
===========================================================================
Persistent Routes:
None

C:\Documents and Settings\hidden>





i blocked the end of my IP with * incase you get confused

[Klonstar]

“YOUR LAN INTERFACE NAME” has to be replaced with the name of the interface connected to the internet
the “Internal” of the last line depends on the language of your windows (e.g. german: “Intern&#8221

I need help, my pc uses german language what have I to write?
Is: "netsh routing ip nat add interface Intern” private" ok?
caus it doesn´t work

My second problem is that, after I type the second line, there comes up:
One port with this name wasn´t registered for this router!

Is this ok?

Thx

[Optimisten]

“YOUR LAN INTERFACE NAME” has to be replaced with the name of the interface connected to the internet
the “Internal” of the last line depends on the language of your windows (e.g. german: “Intern&#8221

I need help, my pc uses german language what have I to write?
Is: "netsh routing ip nat add interface Intern” private" ok?
caus it doesn´t work


I have the same problem, don't know what to write, and i use danish XP.

[AlmostRandom]

Type the following into a command box

netsh interface show interface
and you should see something like this:



C:\>netsh interface show interface

Admin State State Type Interface Name
-------------------------------------------------------------------------
Enabled Dedicated Bluetooth Network
Enabled Dedicated 1394 Connection
Enabled Dedicated Local Area Connection
Enabled Dedicated Local Area Connection [802.3]
Enabled Internal Internal
Enabled Loopback Loopback


As you can see I have the english version of XP so Internal is shown as just that - what you need is what it says for the Interface name for the Internal entry.

Hope that helps.

[rlachenal]

I got it working with Windows XP, altough I was hoping it'd work with linux because now I have to connect through my laptop.. Well, anyway I'm not sure if this helps but I set my DNS servers manually in the phone (the same place where you define the proxy) and no need for proxy here.

Agiler Messenger & Wireless IRC work without problems :)


I envy you. I'm still could not get the thing to work with WinXP or Win2k without using a proxy.

Anyway, I was able to make it work with Linux. Posted my lengthly and confusing step trail at http://www.rlachenal.com/bluetooth-6600-linux/

Hope it helps.

[powser]

Hey.. The page says that it will have problems with the new 6600 firmware. Has anyone succeeded in getting it to connect with the new firmware?

[filo84]

i have an adsl modem (ericsson hm210dp), can i use this method for use my internet adsl on my nokia 6600??

[Brodahood]

Hey Grave... Ive tried as u ve explained but sad to say no success.... everything is done fine and i get the light blue screen on gnubox, and i connect my phone to the comp through the bluetooth serial port, but when i connect from the wap browser in the phone it says connecting Bt and after a while gives an error saying "Internet: Unable to connect please check connection settings" plz help!
Thanks

Broda.

[420whitey]

keeeeeeep trying and rechecking ur settings :-? i format my pc and took me one week to get it working again :lol: :lol:

[maddog17]

im going mad i want to get this damn nokia 6600 up and running for bluetooth internet but im so stupid with these settings lol! im stuck on number 16 people. :

netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full.

what the hell is my LAN INTERFACE NAME in full i have no idea where to get it from please help me someone :-x :-x :-?

[420whitey]

go to My Network Places, its the name of your internet connection, mine was called "Local Area Connection"

[maddog17]

go to My Network Places, its the name of your internet connection, mine was called "Local Area Connection"

hi i done that but still no damn luck what is going wrong i have no idea i have a router if that makes any difference. :sad:


PROBLEM SOLVED i done it i am now on the bluetooth internet 8-) :)

[FiniX2k4]

" 16. run cmd.exe and enter the following commands: "
"netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full"

can't do that because i'm using an usb ADSL connection, apears as a dial-up connection. Any ideas to help me on this step?



Hey im on a USB ADSL witch appears to be as a Dial-up how can i go around this problem and use my computers internet on my nokia 6600

[h4v0c]

dude i've done it all
copied all the settings and stuff ... the only prob is that when i use GNUBOX
and click on 2box direct .... to use Bluetooth
it gives an error saying GNUBOX: Already In Use!
whats the for man ???

[FiniX2k4]

i woulndt have a clue im still trying to make mine work,

i have a D-link 200 ADSL usb modem witch goes under as dialup, thats why i cannot router it what can i do to use bluetooth internet on my nokia 6600 please its important

[Lamp2k4]

I can't get it to work..

Just a question to start up when it says :
netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private

"ip" should be replaced or not???? for my part I haven't and it doesn't work..

Second question: Should I untick all the port in mrouter?? to get it to work?

Other question: when i try a connection in opera i can see my phone trying to call 2222!! it says something like "number cannot be used or dialed up"..

FAct: i keep an eye on my Network Connections for incoming connection (showing details) it always stated: No clients connected :((

4th question: Is there a gateway ip adress to put in the configuration of the nokia ?

Last one : In direct connection, 10.0.2.1 - 10.0.2.254 equals to what? to the range of ip of the nokia 6600??

Those question might be questions of noob but really .. im trying to get the whole thing.. and later i will write a NOKIA 6600 INET over BT for noobs :)

Thx for replying me

[AlmostRandom]

>"ip" should be replaced or not???? for my part I haven't and it doesn't work..
It should not be replaced. ip is part of the command

>Second question: Should I untick all the port in mrouter?? to get it to work?
Yes, all of them should be unticked.

>Other question: when i try a connection in opera i can see my phone trying
to call 2222!! it says something like "number cannot be used or dialed up"..
Sometimes gnuBox has a bug that causes this to happen. Try setting selected 2box, direct, and Infrared in the menu, and then 2box, direct and bluetooth again. That will usually sort this out. If it doesnt fiddle some more like this and you should get it working. This problem was very annoying for me! I think when it works gnuBox will actually remove the number from the access point and if you try and edit it in the normal access point thing, it will moan and say it needs a number when you try and go back- so don't try after its working! (if you do, just switch phone off and on again).

>FAct: i keep an eye on my Network Connections for incoming connection (showing details) it always stated: No clients connected :((
You wont due to above problem.

>4th question: Is there a gateway ip adress to put in the configuration of the nokia ?
No this isnt needed.

>Last one : In direct connection, 10.0.2.1 - 10.0.2.254 equals to what? to the range of ip of the nokia 6600??
Yes, the ip given to the 6600 will be somewhere in this range. When works, you can see the address assigned by clicking on the taskbar dial up icon and selecting details. My network starts on 192.168.0.* so I use 192.168.1.2 to 192.168.1.200 to keep it close (for convience).

[MozzyTM]

i feel like a n00b
how do i get into the mrouter properties?

does it matter that i have a bluetooth usb dongle? im running a cable modem and windows xp, if someone could help me out id be very greatfull

[FiniX2k4]

u guys still didnt answer my problem seriously i need help with it, i cant seem to work my BT internet since i have a external usb modem it registers under dial-up what must i do to fix this problem?

[MozzyTM]

i got it all to work!!!! messenger in the garden! WOW. anyway.. my girlfriend wants me to sort her phone with this. she has a 7610, do i just follow the same setup? a speedy answer would be appreciated

[petermd]

hi,

got it to work eventually - thanks to everyone

few things i noticed..

- ip nat etc etc commands didn't work till i restarted computer, so don't panic if you get a "nat not installed" message
- disabling the bluetooth lan access server wasn't enough - I had to go into Device Manager (right click on My Computer -> Manage -> Device Manager) and uninstall the driver.
- use the "select irda" then "select bluetooth" trick to get the connection set - the phone number should disappear - and then select the access point - phone should open the BT connection by itself if all is well

Good luck!

[s26f84]

i tried all the stuff u guys wrote but nothing works for me. i am able to connect my mobile to pc via bluetooth using nokia pc suit. but i am not able to get the damm dial up internet of my pc on my mobile. i got windows xp and nokia 6600 plzzzzzzzz help.....

and could anyone tell me how to connect the internet of my mobile to pc.... i tried http://www.gprs.kz/settings.pc.html the bloody thing also not works ...plz help guys

thanks sunny

[Zhock]

can ngage do that thing too ?

[Neophyte88]

offcourse, read TZEONN's FAQ over at the faq section

[Libre]

Hi
I tried do connect my nokia 6600 with bluetooth connection PC- Internet
Im using wireless at home,,,,

netsh routing ip nat add interface Internal private ??? wich name i have to put in Internal with portugues win XP ?

with y phone i connect sucess to BT .... but i dont have internet in phone

i always get could not connect to remote server !!!

thnx

[TriFire]

When i enter this line below i get a message saying: NAT must be installed first. Can anyone help me out here??

netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full

[enforcer]

hi guys
u r doing a great job here.

i am a newbie and i have got confused after reading this complete thread.
i have winxp with sp2
my nokia 6600 OS ver 4.09.1
i am connected to internet via vpn connection which give me ip in range 172.x.x.x

i am connected to my isp via a lan connection with my ip set to 10.64.7.124

i also have a internal lan(home) which is setup in ip range 192.168.0.x .
and the internet connection is shared on the above network using internet sharing provided by winxp.

(local connection 4) is the bluetooth network server.

here is what my pc shows after the command "netsh interface show interface"
C:\netsh interface show interface

Admin State State Type Interface Name
-------------------------------------------------------------------------
Enabled Dedicated Local Area Connection 4
Enabled Dedicated Home
Enabled Dedicated Fortunenet
Enabled Dedicated Local Area Connection 6
Enabled Internal Internal
Enabled Loopback Loopback



so please guide me on how do i go about connecting to internet on phone using my pc connection.also i read somewhere in the post that internet sharing has to be disabled.
but can this be bypassed coz or elese my internal network wont work as this pc provides ips to all other pc in the internal network.


hope to get reply.
also sorry for troubling u guys and wasting your precious time.

thank you

enforcer

[tareckinho]

hi to u MR.grave,thanks for your effort.i only wanted to know your email so that i will comunicate with u .i would like to have friends that are intrested in computer.anyway my email is [email protected] or [email protected] hope to get your reply soon.my name is tareck and ill like to know yours.

[slimanus]

one question how do i copy and paste on my 6600?im too lazy to type tht thing in the login script and even if i do it'll b very mistake prone...so how?
and btw my bt cable says 50m raange but the guy says 10m so how much is it roughly in a concrete house?

edit
sorry and also i dnt get the part where u del the bt connection on the comp my del button could not b clicked basically i dnt get steps 15-17 can some1 write aguide for dummies like me for those steps

[Cause4C]

When completing the command "netsh interface show interface" all i recieve are these results leaving me with no interface to use, whats wrong..


Admin State State Type Interface Name
-------------------------------------------------------------------
Enabled Connected Loopback Loopback
Enabled Connected Internal Internal

When i enter "Realtek" which is what displayed after the command "netsh interface ip show config" i still cant use this as the interface..

Any ideas on what im doing wrong..

Im using Windows 2000 Pro (latest drivers)
Nokia 6600 (V 4.09.1)
And have a D-Link DSL-500 router

All other settings so far have been sweet..

All help much appreciated..really want bluetooth internet on my phone.

[Fking]

Advanced Settings: Use Login Script Yes
Advanced Settings: Login Script
i do not have these options on my 6600 (i think it's with the last software)

[frvjum]

Type the following into a command box

netsh interface show interface
and you should see something like this:



C:\>netsh interface show interface

Admin State State Type Interface Name
-------------------------------------------------------------------------
Enabled Dedicated Bluetooth Network
Enabled Dedicated 1394 Connection
Enabled Dedicated Local Area Connection
Enabled Dedicated Local Area Connection [802.3]
Enabled Internal Internal
Enabled Loopback Loopback


As you can see I have the english version of XP so Internal is shown as just that - what you need is what it says for the Interface name for the Internal entry.

Hope that helps.
I have the English version of W2k, and I get:
Admin State State Type Interface Name
--------------------------------------------------------------
Enabled Connected Loopback Loopback
Enabled Connected Internal Internal
Enabled Connected Dedicated Local Area Connection

I type netsh routing ip nat add interface "Internal" full and it says The interface 'Internal' does not exist. An interface with this name is not registered with the router, what should I do??? :sad:

[eastcoast]

hi i was just wondering if this could work on a nokia 9500??

thanks

[grave]

huh, so why dont u use wlan with 16x the speed of bluetooth...?

[whoppass2003]

How-To - Internet over PC with 6600 (wap2)

4. run the program you installed at step1 (gnubox)
5. inside gnubox: Options-> 2box Direct -> Bluetooth, select your computer, leave gnubox running in background
6. run the nokia wml browser select "Bt" as access point and connect :D


Edited by GeeZuZz: I have uploaded and attached the gnubox6600.sis application to this post (zipped).

ok ok ..i have a 7610....and in the gnu boax when i do Options-> 2box Direct -> Bluetooth
it shows the following

Loading CommDb
CSD/GPRS settings
DialOutISP
Description:
DefaultTelNum :2222
ModemBearer
No Nokia Modem

its not happning :-x

in my 7610'z advanced settings...there other options such as Phone ip address,primary name server,secondry server,proxy server address,proxy port no.,use call back,call back type,callback no. which i have left to whateva their default settings were :???: .....what am i doing wrong

[engage]

:P Thanks to the instructions here I've got my bluetooth internet sharing working.

Found this other webbie http://www.dotdoh.com/howto/index.php?=0001 (http://www.dotdoh.com/howto/index.php?index=0001) that had some pretty good flash videos on how to setup the connection.
:grin:

[mib1800]

Hi

Did anyone got this to work for 6670.
I follow the step to setup. Gnubox shows the blue screen.
When I try to use the phone web browser to connect, it prompts whether to connect to server and it give "Already in use" error..

Can any1 help?

[dannyogolo]

hello friend,
someonepls help me share my pc internet connection with my 3230,

thanks to all,

dannyogolo

[mib1800]

Hey, finally got it to work with my 6670. Now I can connect to Internet. AgileMessenger is also working.
Hurray!!!

Note: PC Suite using BT can also work concurrently. BUT you have to connect your phone to Internet FIRST before you connect PCSuite using BT.

This ONLY applies to those using cable modem/adsl with a ROUTER installed (i.e. your cable/adsl modem is connected to WAN port on the router). If you dont have a router, I suggest you invest in one since it is very cheap now.

Phone:
1. Do as previous instructions
2. Set Phone IP to "Automatic"
3. Set "Primary Server" IP to your gateway/router IP. (In your PC run command ipconfig/all to get IP).
(Run the following steps after you setup your PC)
5. On your bluetooth and pair your phone to PC. Set to "Authorised"
6. Run Gnubox. Click Install->Create Records. EXIT GnuBox. Run Gnubox again. You should see something like "BTCOMMS:5". Click 2Box->Direct->Bluetooth. exit gnubox.
7. Run your browser and browse and external site. You should see your phone connect to BT (icon on PC turn green). You should also see a network connection icon in the "Network Connections" (open the Status to see traffic). Happy SURFING.

PC:
1. Ensure your PC Suite is not using BT connect. In PC Suite "Manage connections", uncheck this option.
1. In BT cfg "Local Services" ensure only "Serial Port" is set to auto start and secure. Set the rest to manual start. Restart your BT service.
1. Add modem - pls see previous instruction
2. Add network connection - see previous instruction
---In Network tab->TCPIP , set to automatic IP and check "Allow caller to access local area network"
---In User tab -> DO NOT check the "Allow connect... without password"
3. Run "Regedit.exe". Goto HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\tcpip\parameters. Set the value of IPEnableRouter to "1".
4. Restart your PC

[hoogar]

hmm i got through except the "netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private" i am getting errors while at this stage,it is telling me that
The interface ''Internal'' does not exist.
An interface with this name is not registered with the router.

Please help me :-? :-?

[Zandis]

dude i've done it all
copied all the settings and stuff ... the only prob is that when i use GNUBOX
and click on 2box direct .... to use Bluetooth
it gives an error saying GNUBOX: Already In Use!
whats the for man ???

Here same problem with gnubox.
Any ideas how to solve that?

Thanks.

[Zandis]

Never mind, google fixed that :)


>I'm also experiencing a problem, when going 2box Direct -> Bluetooth I get an >error:
>
>"gnubox: Already in use"

i've had the same problem, i hadn't named the access point correctly, should be "Bt" not Bt(01) as i'd got it. That fixed it.

[Zandis]

Yes, it's really working... over proxy server ;)

[asadali]

How-To - Internet over PC with 6600 (wap2)

i tried the posted link and did what was written there and i just got it to run! it means my 6600 connects to my pc and CAN use its internet connection!
tried it with the nokia standard browser, opera and wirelessirc1.8!

my system is windows xp and i just followed the instructions on http://www.cs.helsinki.fi/u/mraento/symbian/bt-ap.html
but ill try to write step-by-step instructions :)

1. Deactivate all the Checkboxes in mRouter (at least the ones of the Bluetooth COM ports)
2. Goto Bluetooth settings and Deactivate everything else in Local services than Bluetooth serial port, note the com port you set as bluetooth serial port
3. Goto Phone and Modem options, go to "Modems" add a new one, activate "I will select it from a list"
4. choose "Communications cable between 2 Computers" from the list (in Standard Modem Types)
5. Select the COM port from step3
6. in the modem settings set maximum port speed to 115200
7. goto Network Connections and create a new connection (wizard)
8. Select “Set up an advanced connection” -> Next
9. “Accept incoming connections” -> Next
10. Check the “Communications cable between two computers” -> Next
11. Do not allow VPN connections ->
12. select a username you want to give access to your pc over Bluetooth (that’s the username you will set on the phone later)
13. in the settings of that connection go to Network select TCP/IP -> Settings
14. set the IP range to something like 10.0.2.2-10.0.2.254 or, what you like
15. Remove Internet Connection Sharing from all interfaces
16. run cmd.exe and enter the following commands:


netsh routing ip nat install
netsh routing ip nat add interface "YOUR LAN INTERFACE NAME" full
netsh routing ip nat add interface Internal private

“YOUR LAN INTERFACE NAME” has to be replaced with the name of the interface connected to the internet
the “Internal” of the last line depends on the language of your windows (e.g. german: “Intern”)

17. if there is a "Bluetooth Network" connection in Network Connections delete it

your pc should now be set correctly :)

go on with your 6600:
1. Download gnubox6600.SIS (http://nokiafree.org/forums/attachment.php?attachmentid=12499), attached to this post (or download here (http://www.cs.helsinki.fi/u/mraento/symbian/gnubox6600.SIS)) and install it on your phone
2. Create a new Access Point on the phone (Setting|Connection|Access points|New access point|Use default settings).
3. Use the following settings for it:

a. Name: Bt. The name is important, the software will look for it.
b. Data Bearer: GSM data
c. Dial-up number: e.g. 2222. It doesn't matter what you have here as long as it's not empty
d. Username: the username you gave access to the incoming connection earlier
e. Promp password: No
f. Password: password for the user on Windows
g. Authentication: Normal
h. Advanced Settings: Use Login Script Yes
i. Advanced Settings: Login Script


CHARMAP [windows-1252]
LOOP 10
{
SEND "CLIENT"+<0x0d>
WAIT 3
{
"SERVER" OK
}
}
EXIT KErrNoAnswer$

OK:
EXIT

be careful that you get it exactly as show here, including linebreaks. You could save it to a file, send to the phone and copy-paste to the settings.
j. Advanced Settings: Use PPP Compression Yes
4. run the program you installed at step1 (gnubox)
5. inside gnubox: Options-> 2box Direct -> Bluetooth, select your computer, leave gnubox running in background
6. run the nokia wml browser select "Bt" as access point and connect :D

thats all i did... sounds much now but i think it was worth the time i needed :)
i hope i could help you guys set this thing up
btw i just streamed a live tv to my 6600 over bluetooth with real helix :)
-----
grave :rolleyes:

sorry for posting twice :) just wanted to be sure everyone reads it
some parts of this how-to were just ripped from http://www.cs.helsinki.fi/u/mraento/symbian/bt-ap.html and following
just fyi not to get beaten by those who really found out how to do it

btw, im off from 21.5. till 28.5.04, so i cant answer messages, but ill answer all your questions (pm) after that ;)

Edited by GeeZuZz: I have uploaded and attached the gnubox6600.sis application to this post (zipped).



Hello Grave,

u r a master-ive been looking for this solution since quite some time&had even lost hope in it.
u r an angel for me!

i went thru yr post carefully & got my things done hwevr i have queries:

1.from step 1 & 2 all that i cud do is that i cud dig out whats the com port number for an outgoing connection (in my case it was com22).but i didnt understand where to find the "mrouter" thing.

2.i installed a new modem (Communications cable btw 2 Computers) but cudnt follow step 15 (Remove Internet Connection Sharing from all interfaces)

3.cudnt understand the "INTERNAL" thing-what is it?u said it depends on the language of yr windows-how to know that? btw im using windows XPSP2 (English)

4.settings for the 6600-under data beared u said to choose GSM data but my phone has 3 options-GPRS, Data Call & High Speed (GSM)which to choose?

wud appreciate a favourable responce from u either here or preferably on my email-asadali<at>asadali<dot>com

thanx in adv
Asadali

[nategreat]

[QUOTE=PhreeZ]"i use gnubox because it is far superior to the other BT -> Internet method.

firstly it allows me to use the built in wap browser, removing the need for some 3rd party browser."

Hi Ive managed to set up gnubox to allow me to use the very limited trial of doris browser via bluetooth using the following instructions but i cant access the internet via my in built wap browser. It seems to connect to the bluetooth but doesnt load anything. Your post seems to indicate that it is possible. Any suggestions would be appreciated. Nathan

"Make sure PC Suite works with bluetooth.

DO NOT configure your mRouter to connect on the same serial port as your bluetooth usb dongle.

Download the gnubox application and install it on your phone.
http://www.raywalk.com/upload/1/8/gnubox.sis

Now you will have to set up the PC connection on your phone:
Settings->Connection->GPRS->Accesspoint [Put name of PC here] Don't forget this!

Create a new Access Point on the phone: Setting->Connection->Access points->New access point->Use default settings

Name: Bt
Data Bearer: GSM data (This is NOT GPRS! you have to change it)
Dial-up number: 2222
Username: RasUser
Promp password: No
Password: pass
Gateway IP Address: 169.254.1.68
Homepage: http://www.google.com/wml

Install gnubox.sis on your phone.

NOW YOU PUT ON YOUR BLUETOOTH.

Run the gnubox application and select:
Options->2box Direct--->Bluetooth.
Now the gnubox application WILL SEARCH FOR YOUR PC!!!!!
It should list the new settings and switch to a light BLUE BACKGROUND if you see this everything works OK. [/B]"

[gjmathew]

Hi, I really don't know where to remove the internet sharing from all interfaces and I don't know my interface name to put in command. Please help how to find it out..tell me how to remove the internet sharing from all interfaces.........pls..