No boot after flash (3310) ! Help

[Clockover]

Hello

I use Rolis DTC3 Flasher. I do an backup image (original) of the phone's firmware. Rolis say that this firmware have any problem and ask me if he must save or not. I save.
I flash the 3310 with the 5.57 (3310) and the flash failed. And now the phone don t boot and Rolix can' t flash him. :-(

message:
"Flash erasing error
must receive 91 00 FF, but receveid FF FF FF
Chek Vpp,Vbat,Voltage, phone type..."


:(

[dr.bizar]

I've seen this problem a few times before...

First of all what cable are using ??? is it home build...
Well anyway check all cable connections, the problem could be a faulty cable...

If that dosn't work try cleaning the connection "PADS" in your phone... also clean the battery connector, if one of the 2 sensor pads in the middle dosn't have a grip the error will ocur...

Write me back if these simple procedures dosn't do the trick

Regards Dr.Bizar

[Clockover]

Thks for your reponse Dr Bizar.

The cable is not home made but commercial.

I have clean the connectors how you are say :-).
The problem is here too.



:(

[Clockover]

And I see just that the phone do anormaly sound when it is connected to computer.

[Manipulator]

that is buzzer sound,is normal,even my phone sound that when i connect it to flash cable.
try to increase the lpt port delay on setup.
hope this can help.

[Clockover]

A ok. But the first time that I connect the phone to flash cable, it don t sound. (I know, it s not well say :-/)

Ok I go try increase the delay.

What you want say by :" hope this can help." ?
My phone will be kill ?

[Clockover]

Always the same problem. :-(

[kOuBy2k1]

I already have the same issue...

for fix it:

- I close Rolis Flasher....
- I deconnect the cable on my phone...
- I reconnect the cable...
- I launch Rolis Flasher...
- I flash new flash file...

verify your cable is connect to your phone and PC as well as possible....


good luck... :)

[NokiaPhreak]

use another battery, this sometime help.

[Clockover]

kOuBy2k1 => I have try this anytime. Always the same problem. I just try with an other flash file, always the same problem but the progress bar is show.

NokiaPhreak=> I haven' t other battery but I try see this. My battery is full.

Thanks all for your help

[kOuBy2k1]

strange... :(

[NokiaPhreak]

I know your battery are full, mine too, but after i change another battery, i can flash without any problem....just try.

[Clockover]

NokiaPhreak=> yes I will try an other battery when I would find this.

kOuBy2k1=> very strange. The "firmware" (i don' t know the good word in english) was cheksum bad. And I have never change this firmware and the phone is new.

What is the voltages of the battery ?

[madmania]

the voltage of the battery should between 4V until 6 Volt in order to power up the IC inside the flasher. but it's depent on your circuit. Sometimes the circuit use voltage regulator, in this case the power supply can put on 9 volt.

My suggest is try to replace the battery with the same size and model :D

[Clockover]

:D ok :D
When I find the good battery, i try.

[Shidoshi]

Hmm...

I've had a problem with a 3310 not turning on after Firmware Update myself.

A friend of mine gave me his phone to unlock, he said it was a 3310 v4.50, so I told him I'd do it. Once I get home, I decide to update it to a 5.57 and add the 3315 features, so I tried, but didn't work, after about 3 tries with 3 different flash files I decided to check under the battery and to my surprise 3330 was inscribed on the label... hehehe, no wonder a 3310 flash wouldn't turn it on :P

I was thinking you could be going through the same thing, but I guess Rolis knows if it's a 3310 or 3330... and since you can't write your backup flash either... ahh well, just thought I'd share my experience ;)

Cheers,
-Dave

[Clockover]

Thanks you Shidoshi.

On the label, under the battery it' s write: Model:3310 Type:NHM-5NX.
I see my phone in 4 hours.

Thanks all for your help.

For the last luck, when there is not hope.
There isn' t a software who flash but without all check ?:)

[caleb_2]

hiya,
had the same problem, but with me it was the software...
exactly the same problem when using Rolis 4.78b, but when using Rolis 4.77 everything is fine, and I have flashed many times with that prog now!
So, my advice is: just try using a different version of Rolis! 4.77 works best for me!


greetz
cal

[username]

This thread really scare me... :( Although, I can't help much but just a word of encouragment.

Clockover... keep on trying . I'm sure you will get it right...

[Clockover]

Thanks all for your help :-)

caleb_2=> Ok thanks, I go try this. (4.77 say me that it' s not the good phone). I continue.

username=> I must because I haven' t money for change this. :-(
But I am confidig. :-)

[Clockover]

I have enough. I really not understand the problem.

I have flash 0x200000 to 0x20F000 successful but flash image bigger than this, there is the porblem.

[Jas1]

If the phones a 3330 flash it twice, once at 200000 and then at 400000 and it works fine.

Try restarting everything, reconnect phone run rollis and hope for the best, This always helps me. Good luck


Jas1:p

[Shidoshi]

Hmm...


Originally posted by Clockover
I have enough. I really not understand the problem.

I have flash 0x200000 to 0x20F000 successful but flash image bigger than this, there is the porblem.

Get another flash file... I thought the 3310 was from 0x200000 to 0x400000...

Try http://nokia.sno.at/ for the flash file you are looking for.

We're here to help each other, so don't give up because we won't ;)

Regards,
-Dave

[Clockover]

I have try:
-rolis 4.77 - 4.78 - 5.13
-and differents flash files.

I continue to try with other files.
:(

[username]

@Clockover

Perhaps its the problem with your flasher cable. Try borrowing it from someone and try it.

Its like you had tried all means to save your phone so I guess it might be the problem of your cable.

[Shidoshi]

Hmm...

Or if you do not have another cable, try using it on another computer, or if you can't do that, try changing the com port, try 1, 2, etc... or try changing the ports themselves (e.g: putting new ones in. I usually have a couple spares around so this usually isn't a problem for me)

I would try a different OS also. If neither of these methods have given a positive result... after that I would most probably be convinced that this is a hardware problem on the phone :)

Regards,
-Dave

[kOuBy2k1]

@ ClockOver...


U can found 3315 French Full Flash File in the Files Section of my Yahoo's group... I have make a tutorial to do it.... in French...


U can try it... ;)

[kOuBy2k1]

click here... (http://fr.groups.yahoo.com/group/nokiaflash/)

[Clockover]

kOuBy2k1=> thks you but I follow your tutorial ;-).

The other=> Ok i go try all what you say (finally as far as possible)

Thks you. I inform you.

[catweasel]

Clockover, I often get the same when I flash with Rolis with me it is due to the port voltage stability "I think" as I am using a laptop.
I don't know what PC you are using but could be the same problem, I keep trying until it works. Don't give up you will win in the end! Good luck.

[kOuBy2k1]

sorry... I don't understand... It's works fine for me... :confused:

[Clockover]

Very interresting ! I use a notebook.
I go see this.

[Clockover]

With the other computer, always an other problem. (freeze)
WinDDP on the Notebook all zone click are locked..

:-(

[nkresource]

i sometimes get this problem, i disconnect phone take battery out, and put it back in connecter then batt. it works fine, i also kept trying it. i does work

[Clockover]

I have do this many time

[prasert]

I has same problem but I lucky than ,I change to use Rolis flasher 4.78b6 can flash agian

[Lapu-Lapu]

Originally posted by Clockover
Hello

I use Rolis DTC3 Flasher. I do an backup image (original) of the phone's firmware. Rolis say that this firmware have any problem and ask me if he must save or not. I save.
I flash the 3310 with the 5.57 (3310) and the flash failed. And now the phone don t boot and Rolix can' t flash him. :-(

message:
"Flash erasing error
must receive 91 00 FF, but receveid FF FF FF
Chek Vpp,Vbat,Voltage, phone type..."


:(

i experienced this kind of error...it's a matter of not having good terminal contacts.