PDA

View Full Version : T610 imei problem



robphp
19-10-2004, 09:19 PM
Hi all,I have changed the imei on my T610 but now it says PLEASE INSERT CORRECT SIM ! With every sim card.I reflashed it with the full flash & T610 modem file.The modem file i used was R1A081 I was told that i should use R1L013.ARM but it could not find it.Any ideas how i can get this little bugger going again.
Rob

soybean
20-10-2004, 06:04 AM
Repair using DIV and "rebuild SP area using OTP imei"

robphp
20-10-2004, 08:07 AM
Hi soybean,Thanks for your reply.I think i may be doing something wrong as i have tried rebuilding the sp area using OTP imei.Could you give it to me step by step as i spent hours on this last night.I am using div8.4 as i could not find div3.1 as instructed by an other fellow user.
:-?

Forhike
20-10-2004, 08:19 AM
hello! pls contact me on icq or msn i can send you everything you need and tell you what to do step for step, to get it to work again

soybean
20-10-2004, 08:41 AM
@Rob
Div3.1 can be download at http://merwin.cellular-support.com
The step is as follow:
1. After Dongle connected to PC, run the SW and connect phone connector to T610
2. Select phone type to T610, select "Rebuild SP area using OTP Imei"
3. Press "Do selected Job"
That's all

Good luck

robphp
20-10-2004, 08:47 PM
Thanks for all your help lads.I am still having problems.I have installed the div3.1 and it go's to 37% and it then says ERROR 0104 Then stops.Where am i going wrong.This poxy phone is getting closer to the bin. :evil:

squidgy45
21-10-2004, 08:45 AM
hi. Firstly, to change imei u need a patched flash file. If u use a normal flash u will get the insert correct card problem.

first flash the phone with a patched file. if it is a newer model then the old R1L013 may not work. I am using a patched r6b file which works great.

then change the imei

u may or may not have to reset gdfs after procedure.

dont use the rebuild otp function as that will reset the imei back to the phones original - sort of defeats the object!

any div soft will do, but the phone is r6a or above u will need div5.0 to remove the rsa protection first.

steve

sergo_zmeia
21-10-2004, 11:47 AM
Seems to me Ur phone is locked on 4 levels...Use this:>,*,<<,*,<*
<> with the joystick...now U are in service menu...U will see option bout sim locks...
dont use div 3.1...find 5.0....or replay me ill upload it for U....
then just rebuild IMEI using OTP option..should work...
Good luck!
Sergo_Zmeia

robphp
21-10-2004, 06:26 PM
Hi both,Thanks for your help!I have downloaded div 5.0 but it is still not playing fair.When i try to run the proggie, it go's to 100% in the first stage but only to 7 % or 12% in the second stage, then stops running.I then get an ERROR 01A1 message.I have tried to reset the gdfs but i get the same problem.Thanks again for your patience, squidgy45 & sergo_zmeia. :???:

soybean
22-10-2004, 08:43 AM
What is Firmware version of your T610? For the error code you can see at www.cellular-support.com, if i'm not mistake it its RSA protection. Please check the RSA protection status, if it's active then remove the RSA protection first, then you can do rebuild, reset, read code, etc. But you need to re-flash the AVR afterwards. ;-)

sergo_zmeia
22-10-2004, 08:55 AM
@rob, clean good the system connector..than the proggy must run ok..
Good luck!
Sergo_Zmeia