PDA

View Full Version : System Failure Contact service provider



lam
27-10-2002, 07:34 PM
Hi guys
What is the correct sollution for "System failure contact service provider" in samsung phones.

Boy
29-10-2002, 05:39 PM
Try to reset it or flash your phone and the result...... you will know it.

Regard


Boy

:)

Albarracin
29-10-2002, 09:19 PM
Samsung system failure contac provider repair solution By Nokiaunlocker:
Open Toolbox4
Go into E2pManager
Press Program on
Selec Eeprom
Then E2pTstPattern at the top of the list
Tick the box that says Write to Eeprom
Then in the input box type the following 0x2767
Then Send command to phone
Then press Reset on the right hand site TWICE
The phone should reboot.

Now try a sim in the phone should be working 100%
This was tested on samsung T100 but it should work on Most if not all modells

Regards

07-11-2002, 01:09 PM
With help of multimeter check 4 and 5 no. pins of eeprom with ground if it is showing continuity or 100ohm check at the system connector side (where you connect the charger) Or else these two pins leads to protection zener diodes (Five pin smd component) replace it or remove phone become normal.

If it showing above 2k replace eeprom or unlock with paderf 4
It worked for me in N200

teknix;)

Boy
09-11-2002, 03:26 PM
Hi,

System Failure Contact service provider mean there is something error with software, its not hardware problem.

It useless if you reset it by Toolbox. The only way is open the correct imei program, and unlock than reset it. It will done in few minutes,

Hoped this can help all people who have the same problem.


Regard


Boy:)

lam
09-11-2002, 03:32 PM
What is the name of IMEI program? if you know any web address to download it.

(The only way is open the correct imei program, and unlock than reset it)

Boy
09-11-2002, 03:38 PM
Hi

@ lam

Try find a link that Mr. ABE post in forum. He give a free ftp that you can download JIG BOX Original software.
Just Find in the forum....cause i will not attrach anything that already attrach in this forum.


Hope its can help you

Regard


Boy

:)

lam
09-11-2002, 03:42 PM
i know the ftp ABE's ftp server and download all jig box files. but
still i cannot repaire any R220 samsung phones(system failure contact service)
lam

Boy
09-11-2002, 03:52 PM
@ lam

Hi,

Maybe you used a wrong box or cable, or maybe u dont know how to used the software.

What you used jig box or something else..

If you want to ask anything just go to my threat "free", i will answer all your question there.

The - End

Regard


Boy Electronic
:)

Warge Master
10-09-2003, 02:31 PM
Hi there

I was wondering where I could obtain a copy of a program that will stop the system failure warning coming up.

I downloaded GSM phone test program v10.0

This program writed by :
Vahid Shahabi
IRANIAN DIGITAL SERVICES

I was attempting to change my IMEI number for my phone. The phone before accepted different sim cards and recognised them but just didnt let me call out.

After loading the T100 file a menu came up and I accidently pressed the shortcut for EEPROM Access (GPSI) . Now when I switch my phone on the phone says

System failure please contact service provider

what can I do? I am really worried I have messed the phone up.
please can you help me please

Thanks a lot
Kindest Regards
M.Ahmad

Thanks a lot for your help



Samsung system failure contac provider repair solution By Nokiaunlocker:
Open Toolbox4
Go into E2pManager
Press Program on
Selec Eeprom
Then E2pTstPattern at the top of the list
Tick the box that says Write to Eeprom
Then in the input box type the following 0x2767
Then Send command to phone
Then press Reset on the right hand site TWICE
The phone should reboot.

Now try a sim in the phone should be working 100%
This was tested on samsung T100 but it should work on Most if not all modells

Regards