"bad data from box"

[j_h_u_n]

Hi! Guys,

Anybody who successfully programmed PIC16CE625?I have program this PIC,hex was came from dk.zip which was posted a few months ago.I follow the procedure, first is to program dex.1 and reset, then program the dex.0. After that i try to put it on my prepared PCB, and Dejan flasher 1.05 and i get this "BAD DATA FROM BOX".
I used the PICPRO hardware and PICALL soft programmer if you heard this kind of programmer.Do i need some pull-ups or pull-down on the pins? Or i have bad hex?


Pls i need your advice or comment very badly!!! i still have one PIC available.I'm thinking to buy PIC16F628,but its too late i have already order 16CE625.So i have get this thing work.

j_h_u_n

[o_MAST]

I have tried box with 16F628 and it works fine!
I think that it say "bad data from box" and not "bad connections" because eeprom area of the pic isn't programmed. After programmed pic 16ce625 with dex1 you have to put it in pcb inserted in lpt port. In this way the pic will work and so it will program the eeprom. Then you have to re-program pic with dex0.

B.r



o_MAST

[j_h_u_n]

Hi! O_mast,

Try to look i attached.This is my first time to to do this stuff.This really procedure i made maybe you'll have an idea to where made wrong.
first i turn on the hardware(PICRPO),then click the picall.exe.
load the dex1.hex conf -XT, PWRTE enabled
put the PIC on ZIP and click progam msg 'program successful'
after that turn -off the hardware for a while then turn it on again.
load the dex0.hex this time error comes up, but continue progamming it
then message comes up again saying the addesses.
after that i put the PIC to to my prepared dejan pcb and and if will work.
But this error comes up.

Can you tell me where did i go wrong?How to reset the PIC?
Can you give me step by step procedure progamming this PIC?
I dont have PIC16F628 so i'm trying this to work with your help or anybody.
So help me pls...

j_h_u_n

[Yasser]

[o_MAST]

Hi, try to press F10, box init.


Bye

o_MAST

[j_h_u_n]

It's ok bro.By the way did you already try to build it?
I visited your new page a while ago and you have interesting soft.actually i already downloaded rollis4.78build005.

Well,i'm really trying to build this box to know and learned what it can do that can't do by Nk_calc and other soft.

I appreciate your great help.

Regards
j_h_u_n

[j_h_u_n]

To Yasser,

It's ok bro.By the way did you already try to build it?
I visited your new page a while ago and you have interesting soft.actually i already downloaded rollis4.78build005.

Well,i'm really trying to build this box to know and learned what it can do that can't do by Nk_calc and other soft.

I appreciate your great help.

Regards
j_h_u_n

[j_h_u_n]

Yes, i already try pressing F10, but no respond it freeze as is.Maybe you have working hex for the chip(PIC16CE625),can you send them to me pls?

Thanks.
j_h_u_n

[o_MAST]

I downloaded the 16ce625 HEXs from welcome.to/kimagsm.

Bye

PS: I have the pic 16F628 and it works fine!


o_MAST

[j_h_u_n]

Hi! o_MAST,
Did you at my procedure?On the other forum i also post my this problem and one said i should reset the PIC after programming dex1.hex.He said this is done by putting the PIC to Dejan circuit brd and plug to lpt port in 1sec. before programming dex0.hex.I did what he has said for my second PIC but no luck,still i got the same message.

What else is the other way to reset the PIC?

j_h_u_n