PDA

View Full Version : T28w Unlock instructions & help?



Renegade42
19-02-2003, 04:57 AM
Hey folks,
I am a newbie so I apologize in advance for my ignorance but we all gotta start somewhere I guess and many of you are miles ahead of me...:)
I have Ericsson T28 World with the AxRxTx cable and the Atr 5.0 and Atr 5.3 software.

I have it connected to a PC serial port and when I run either of the ATR programs to unlock or read the eeprom and stuff it first says to press the <NO> for a short time and when I do it simply times out! That is all I can get it to do is TIME OUT!

Yes the phone turns on and off when I press the <NO> key but it acts like it never sees the phone attached at all!

Can ANY ONE of you EXPERTS out there give me proper instruction to unlock this phone.

Oh by the way..it is a North American phone.

Thanks in advance..
Please reply to this e-mail:
[email protected]

gorandj
19-02-2003, 11:22 PM
check ur cable, clean connector on the phone

superman
24-02-2003, 05:23 AM
use atr53 only and make sur u have the right cable, I believe u got the wrong cable.

janosandi
24-02-2003, 11:00 AM
I have the same problem but i found a program from italian site
your problem is in the cable if you can build some modification to your cable i will send you the right schematic

Renegade42
24-02-2003, 06:29 PM
Well, I have tried EVERYTHING suggested by all of you wonderful people here on the thread but nothing seems to work. It was suggested that I might have the wrong cable but according to TechGSM it is the same cable that they use just fine. I have tried it on three separate computers with Win98 and ATR53. The serial ports were confirmed to work properly. I will now check out the info regarding cable modification posted to me previously and see what happens. One thing I did mention to TechGSM is that the cable they sent to me says "T29" on the serial end and they still insist it will work...hmm. I wonder if the new cable is bad or the phone has a problem. I have cleaned the pins. Oh well, I will see what the cable modification does when I get it.
Thanks to all of you for your great help.
P.S. I have also tried ATR5.0 as well.
Vic

janosandi
24-02-2003, 10:20 PM
Hello dear
you need some electronic knowledge to make that
i test 4 kind of cables & all not working
in the program left down there the schematic of the right cable you need

more help
[email protected]

superman
24-02-2003, 10:42 PM
I mest up once a t28w with the atr50, dont use it, use atr53. and I had a pc once where the com port did not work. Use win98. Everytime u try to use atr53 take out the battery for a view seconds and back in sometimes it takes a view trys doing that. But it seems yr cable is the problem.
Good Luck

dialtone
02-03-2003, 04:57 AM
Though I'm not an expert, I suggest you two things :
(1) Hold the cable connector tightly pressed against the phone while you work. If necessary take help of soemone to do it while you work on Computer keypad.
(2)Press "NO" immediately when asked to, without any delay. Timing is important, I think.
Wish you all the very Best !

Aregbesola
02-03-2003, 07:08 AM
If all suggestions above still don't work , Before you take your cable apart try using another computer.
I cannot explain this ,but i've had similar problems with a t28 phone and after trying everything with no success i just tried on another computer and it worked with thesame cable and phone and for no special reasons or maybe confiquration problems i don't , so try everything.

amigo
14-03-2003, 01:31 AM
No men there is no problem in cable , problem is that your phone
T28w is TDMA. ATR 5.0 or 5.3 don t work with flash in that phone.
I think solution for unlock is this:

1.First flash phone with flash from "normal" T28
2.Unlock with ATR 5.0 or 5.3
3.Back flash from T28w with ATR 5.0 or 5.3

If you want flash for T28w email me.

superman
14-03-2003, 03:03 AM
The t28w (world) is not tdma it is GSM 900/1900 Mhz mostly sold in the USA for use on "their" band 1900Mhz. There is no normal phone (what is normal?), the other T28 is the T28s which is the european or rest of the world model (but USA, Canada, certain islands in the caribbean and some countries in south america like chile and el salvador etc.) which uses GSM 900/1800 Mhz.
But on both models the ATR 5.3 software works to unlock etc.
And of course both the T28w and the T28s use simcards.

Salami1_1
15-03-2003, 03:33 PM
Well the T28W is a real pain in the ass!
I have one here that also just does NOT want to unlock.
I flashed many flash files and uplaoded many eeproms .. but still unlocking does not work :S
All programs say 'unlocking done All locks are cleared'
but still I get the message: 'place correct simcard'
When the phone has T28 W eeprom and T28s flash it says:
0x000F4 (that all it does)
with T28s flash and eeprom it just doesn't want to unlock...
with the T28W flash and T28w eeprom it also does not want to unlock. With T28W eeprom and T28s flash it also just does not want to unlock :(

if anyone knows solutions pls help me!
thnx!
WBR
Salami1_1

Alinus
16-03-2003, 08:28 AM
maybe sim reader is broken inside phone....-:rolleyes: --:rolleyes: :rolleyes: :rolleyes: :rolleyes:

gorandj
16-03-2003, 10:02 AM
does your phone ask for `insert correct card` without sim card? or when a card is inserted?

superman
16-03-2003, 02:57 PM
get a working T28w and read flash (*.sbn) and e2 (*.bin) from the same and write it back in the bad t28w and then unlock with atr53, u cannot interchange t28s and t28w files. use varanius11 together with gsm-magic to read and write flash and e2. I posted before good t28w flash and e2 and the varanius11 with gsm-magic. e2 and flash must be from the same phone u cannot take one flash from one phone and a e2 from another and mix together.