i m here to help u

[kingofcellular]

if any one need help about gsm conselted with hardware or software i m here to help i love to help others send me urs emails
my adress is
[email protected] :cool:

[kingofcellular]

no one neened help if any one need post his/her problem i will glade to help ok t/c ;)

[janosandi]

Hello
I think i have a problem that is i'm newbie & i have heat station but i dont know how to work with it
can you help me any way

thanks

[kingofcellular]

U hve rework station wht do u know about it wht ru hveing probelm which company product ur using give me explaination thanx t/c ;)

[markchee]

i HAVE A 8250 WITH NO NETWORK,please advice,thanks


mark

[janosandi]

i dont know how to make a solder balls on the smd

[kingofcellular]

U hve to put ic in smd ur ic should be located in perfect direction u can see ur ic points in smd hole ok then put soldering past in it n press the soldering paste in points that the paste go into the bottom ok then heat it Air should be on 2 n heat should be on 5 ok best of luck ;)

[janosandi]

Thanks for your reply i will test it
i have 3310 when i turnit on it lights for a second and off so i must reinsert the batery again to do that when charging is flashing on off on off i think its a short circuit on startup
have you any idea

thanks

[cspatel3333]

hi there i have a 6210 that boots up and everything but after one night that i dropped it the reception does not work. I have replaced the arial with a friends one which was working but still no success with reception
please advice or contact private on [email protected]
thank you

[s1emens]

I need help on my 3330, it only can charge using Ni-mh battery, but it will show no charging when i use a Li-on battery, any idea... thanks

[cspatel3333]

i have just bought a data cable with different extentions for different phones. The problem is that the computer does not pick up the data cables when i try to use a unlock program. the cables supposedly switch between mbus and fbus automatically I use windows xp on a laptop and have no idea how to configure the system if that is the problem. I have also tried to use a friends laptop who also uses xp but neither computer picks up the cables
please help/advice
cheers

[kingofcellular]

xp dont suport the mobiles software lots of software didnt work in xp try the program in WIN/98 BEST OF LUCK ;)

[cspatel3333]

i have tried opening the software in windows 98 but still sake problem

[killer04]

Could u tell me where to get memory chips for nokia 3310.I need a 6mb one

[shevchenko]

have u got the dct4 imei changer @ 'kingofcelular'

[kingofcellular]

This time no one get imei changer of dct 4 lolzz every body is making fake imei changer but soon u will get ;)

[kingofcellular]

Ok wht the error is coming tell me complete whts wrong with the cabel

[pico]

and who you think will release dct4 imei change solution?
please note you will never just have just a software solution to imei change in dct4, extra voltage needs to be apllied when trying to write OTP area of IMEI data if you wish to break protection.
Original NMP uses jbv-1 jig connected to external psu..

b-phreaks will not release dct4 imei sol.
jic is same

[cspatel3333]

to kingofcellular
i will use the example of the software nokia tool by rollis. When i connect the cables to my computer when i click on clear sp lock it says failed to initialise local mode. Then when i click on interface auto setup i searches the all four ports but says that no connection is found. Similar results are found when i use other programs

[killer04]

Originally posted by killer04
Could u tell me where to get memory chips for nokia 3310.I need a 6mb one

i also need a 4mb ic flash memory

[kamaroy]

hi,

My 8210 got an error message "phone ram is bad" whenever i try to flash my phones. I just realize the problem just after i've put it in ultrasonic cleaner & reflowed using rework station. I've try to flashed it with different program like dejan flasher, rolis 4.78 etc. but same message appears.

Pls help

[kingofcellular]

did u chek the sercet board if the ram or mad prints broken the problem bad ram will come or the ram damege it also get problem ram bad or the last MAD change the mad the problem will gone best of luck

[pico]

i think you have problem at flash ic, cos of reflow..
try reflow flash ic, but maybe you need to remove/replace..
just a thought :)

[ahib]

@kingofcellular I recently sent &recvd an 8890 to someone on this forum who was selling repir srvice!howevr it still has NO signal whatsover pls advise what it could be-Im under the impression the guy changed PA-I can see flux around sheilding-BUT the ant switch looks untouched as is the FDK!

[kingofcellular]

change the antina swicth then if same foult change COBBA ic n then chek if its not work so change HAGGAR BEST OF LUCK

[m1tch]

what are these and where are they located on the 8210 and the 3310?

cheerz

[pico]

IC = Integrated Chip (Integrated Circuit..)

Nokia phones contain a few ASIC's (Aplication Specific Integrated Chip), basically chips Nokia have made that do a certain function (or number of functions).

CCONT IC is the power controlling IC

CCOBA IC is the audio codec, a/d-d/a converter..

HAGAR is the RF (Radio Frequency) IC

also you have the MAD IC which is the CPU of your phone

and you have CHAPS IC which is charging control.
in older phones such as 5110 thiat is PLUSSA IC

this is all DCT3. DCT4 has different IC such as UEM, UPP.... :)

where are they?
just open the phone :)
any small black squares on the board are your ASICs

apart from one which is the Flash IC, for 8210 that is 16MB flash and 2MB sram storage chip.

hth :)

[wings]

Originally posted by killer04
Could u tell me where to get memory chips for nokia 3310.I need a 6mb one


Contact me


BR

[wings]

Originally posted by kingofcellular
change the antina swicth then if same foult change COBBA ic n then chek if its not work so change HAGGAR BEST OF LUCK


:D :D :D :D :D

BR

[m1tch]

so,if i had a reception problem. eg. my signal keeps coming and going on my 8210, how would i solve this? i changed ariel, etc, but still no luck. also can u plz post some diagrams of the chips and where they are situated plz?

thanx

[pico]

please,
dont be so lazy.
search old posts for your problem..