3210 flash write problem

[baraka42]

hi all.

Happy New Year to all.

i have 3210 it saw as below during write flash. any help ?

Lead's kNok-Phoenix - build 1
based on kNok - Engine build 22, Frontend build 18

Thanks goes out for the following:
Dejan, Kodo, Viper, Jozso (for hardware and cable support
and of course beta testing), Bph&Co, Saras, IceDragon,
Steina, Epilog, Invisible, Jethro, H-tom, AlAraf, Lead
and all the others who supports knok...
misc_calibrate_delay : 897.84 BogoMIPS
FLS1_GetFlashParameters : parameters found NSE-8(3210) - DCT3BT2.TIA
FLS1_PreparePhone : found flashing params NSE-8(0) - 61, 06
FLS1_ConfigurateBootstrapDCT3 : checksum is 4E8B
FLE5_DirectInitialiseBootstrapDCT3 : Press power on (if needed)
FLE5_DirectInitialiseBootstrapDCT3 : executing bootstrap
FLE5_DirectInitialiseBootstrapDCT3 : preparing reading phone RAM
FLE5_DirectInitialiseBootstrapDCT3 : executing reading phone RAM
FLS1_GeneralSendBootstrapDCT3 : bootstrap seems to be running
FLS1_PreparePhone : invalid NMP returned in phone RAM
FLS1_PreparePhone : detected NMP is NSE-8
FLS1_GetFlashParameters : parameters found NSE-8(3210) - DCT3BT2.TIA
FLS1_PreparePhone : searching algocode for 8900, 9088
FLS1_SearchAlgoCode : searching flashid in config\flashid.cfg
FLS1_PreparePhone : internally detected algocode - IW28F008.TIA
FLS1_SearchAlgoCode : searching flashid in config\algocode.cfg
FLS1_SearchAlgoCode : cannot open config\algocode.cfg
FLS1_GeneralSendAlgoCodeDCT3 : algocode is loaders\IW28F008.TIA
FLS1_GeneralSendAlgoCodeDCT3 : forced flash size is 0
FLS1_GeneralSendAlgoCodeDCT3 : flash end is 00400000
FLS1_GeneralSendAlgoCodeDCT3 : checksum is BF8E
FLS1_GeneralSendAlgoCodeDCT3 : algo code seems to be running
FLS1_DummyWrite : trying
FLS1_Write : written block (4 bytes) starting from 00200034
FLS1_Read : read block (256 bytes) starting from 00200000
FLS1_DummyWrite : trying
FLS1_Write : written block (4 bytes) starting from 00200034
FLS1_Read : read block (256 bytes) starting from 002E2F74
FLS1_GetPhoneInfo : cannot get MCU version
CMD_handlecommands : cannot analyze phone

thanks in advance

[gabiz]

Hello and Happy New Year ! to all.I ussualy use Knok only for erase full flash and for other things but for flash a nokia phone rolis is the best program.So try to use it and you'l see. Good luck!

[iki_tenggo]

i'm using knok 22 manually erase flash from 0x200000-0x2EFFFF and then 0x2FFFFF-0x400000, after that write full flash from 0x200000-0x400000 to 3210, that's my way maybe can help.

[baraka42]

thanks m8s.

as you i try. result is here.

kNok - Engine build 22, Frontend build 18
Thanks goes out for the following:
Dejan, Kodo, Viper, Jozso (for hardware and cable support
and of course beta testing), Bph&Co, Saras, IceDragon,
Steina, Epilog, Invisible, Jethro, H-tom, AlAraf, Lead
and all the others who supports knok...
misc_calibrate_delay : 884.73 BogoMIPS
FLS1_GetFlashParameters : parameters found NSE-8(3210) - DCT3BT2.TIA
FLS1_PreparePhone : found flashing params NSE-8(0) - 61, 06
FLS1_ConfigurateBootstrapDCT3 : checksum is 4E8B
FLE5_DirectInitialiseBootstrapDCT3 : Press power on (if needed)
FLE5_DirectInitialiseBootstrapDCT3 : executing bootstrap
FLE5_DirectInitialiseBootstrapDCT3 : preparing reading phone RAM
FLE5_DirectInitialiseBootstrapDCT3 : executing reading phone RAM
FLS1_GeneralSendBootstrapDCT3 : bootstrap seems to be running
FLS1_PreparePhone : invalid NMP returned in phone RAM
FLS1_PreparePhone : detected NMP is NSE-8
FLS1_GetFlashParameters : parameters found NSE-8(3210) - DCT3BT2.TIA
FLS1_PreparePhone : searching algocode for 8900, 9088
FLS1_SearchAlgoCode : searching flashid in config\flashid.cfg
FLS1_PreparePhone : internally detected algocode - IW28F008.TIA
FLS1_SearchAlgoCode : searching flashid in config\algocode.cfg
FLS1_SearchAlgoCode : cannot open config\algocode.cfg
FLS1_GeneralSendAlgoCodeDCT3 : algocode is loaders\IW28F008.TIA
FLS1_GeneralSendAlgoCodeDCT3 : forced flash size is 0
FLS1_GeneralSendAlgoCodeDCT3 : flash end is 00400000
FLS1_GeneralSendAlgoCodeDCT3 : checksum is BF8E
FLS1_GeneralSendAlgoCodeDCT3 : algo code seems to be running
FLS1_DummyWrite : trying
FLS1_Write : written block (4 bytes) starting from 00200034
FLS1_Read : read block (256 bytes) starting from 00200000
FLS1_GetPhoneInfo : cannot get MCU version
CMD_handlecommands : cannot analyze phone

any more idea ?

thanks for your time to reply.

[James18]

Recently I have flash my 3210 with Rolis and I don't have a problem on it. And don't forget to update the faid via Eeprom Tool.

Hope your unit will bring back to normal.

[gsmtech-SK]

You must connect +3 Volts to pin Vpp!!! It is needed only with 3210 (not all versions).

[baraka42]

@ james 18,

this phone is FU____ with sw by mistake by me. so your

sugession can't work for me. it's for normel phone. thx.

@ gsmtech -SK i will post result after try as you.

thanks of both for time to reply me.

[gabiz]

Try to flash phone with Rolis flasher but load separatelly MCU and PPM ,in that case rolis flasher say updating 0.....02000.. area (Dont't know what is that area but must be something)and maybe you can flash phone that way.
Good luck!